1
Hobby & gaming
Elektron Digitakt II angled stand
This is not a fixed STL. SpeakCAD generates the elektron digitakt ii angled stand to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a pair of 15° side stands for an Elektron Digitakt II, 170 mm long, 20 mm wide, 45 mm rear height, 2 mm front lip, TPU foot recesses.
What a elektron digitakt ii angled stand is
A pair of side stands that tilt an Elektron Digitakt II (215 × 176 × 63 mm) 15° towards you so the screen and trig keys are easier to read. Each stand is 170 mm long, 20 mm wide and 45 mm tall at the back, with a 2 mm lip at the front and TPU feet recesses. The rear stays open for the jacks and power. Print on their sides in PETG.
Syntakt and Digitone II share the same case and fit, but the Model:Cycles and Model:Samples are smaller. Open the ready-made model in SpeakCAD for free, change the angle in the viewer or the chat, then download the STL.
People also search
digitakt ii stand stlelektron digitakt stand 3d printelektron angled standsyntakt stand 3d print
Questions people ask about a elektron digitakt ii angled stand
A pair of side stands that tilt an Elektron Digitakt II (215 × 176 × 63 mm) 15° towards you so the screen and trig keys are easier to read. Each stand is 170 mm long, 20 mm wide and 45 mm tall at the back, with a 2 mm lip at the front and TPU feet recesses. The rear stays open for the jacks and power. Print on their sides in PETG.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a pair of 15° side stands for an Elektron Digitakt II, 170 mm long, 20 mm wide, 45 mm rear height, 2 mm front lip, TPU foot recesses.
Syntakt and Digitone II share the same case and fit, but the Model:Cycles and Model:Samples are smaller. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More hobby & gaming
Flydigi Vader 4 Pro display standA stand that holds a Vader 4 Pro at 25 degrees with the RGB face visible and a 14 mm USB-C slot.Nintendo Switch 2 tabletop stand with USB-C gapA tabletop stand for the Nintendo Switch 2 (272 × 116 × 13.9 mm with Joy-Con 2 attached) that holds it at 65 degrees with a 16 mm deep slot and leaves a 20 m…Sim racing wheel wall hangerA wall hanger for detached sim racing wheel rims (most GT and round rims are 270 to 320 mm across) that holds the rim on a 50 mm wide curved cradle with a 15…Board game token tray with scoopsToken trays sort cardboard chits and wooden cubes into compartments with sloped scoop bottoms so you can pick pieces up with a fingertip.Steam Deck OLED dock stand with USB-C cutoutA desk stand that holds a Steam Deck OLED (298 x 117 x 49 mm) at a 15 degree lean while a USB-C hub or the official dock's cable stays plugged into the top p…Steam Deck 2 travel kickstand with case lipA clip-on kickstand for a Steam Deck 2 (about 300 × 120 × 50 mm) that still clips over a Jsaux or dbrand case.