Bracket and wall mount generator

Brackets and mounts from the numbers that matter: the screws, the spacing, the load

A bracket is a few numbers: what it holds, how far from the wall, which screws and how far apart. SpeakCAD turns them into a part you can print. A flat mounting plate or adapter plate you make by hand from the plate shape: holes sized for M2 to M8 screws with a countersink or a counterbore, copied in a row, a grid or a circle, slots for adjustment, free, download included. An L-bracket, a shelf bracket, a pipe clamp or a wall mount for a device you describe to the AI, which adds the fillets and the thickness that carry the load. STL, 3MF or G-code sliced for your printer, on a phone or a computer.

Free account, no card: the hand tools and their downloads. Your first AI part is on us too (some accounts confirm it with a card first, nothing charged that day). A download of AI work spends 4 credits and each further new part 3, a small change 2, with Maker at $7.99 a month for 50 credits, every download included.

How it works

From the screw pattern to a bracket on the wall

Measure the hole spacing and the screws you have before anything else: they are the numbers a printed bracket most often gets wrong.
1

Start from the plate, or describe the bracket

The plate shape is a flat plate with rounded corners; its width, length, thickness and corner radius are numbers you type in the viewer. For an L-bracket, a clamp or a mount shaped to a device, describe it in the box above with what it holds, the screws and the spacing: one AI request (4 credits on a plan, 3 without one).
2

Drill the screw holes

Tap Hole, pick the screw size (M2 to M8 clearance presets), choose a countersink for flat heads or a counterbore for socket heads, and type the centre in millimetres from the edges. Duplicate puts the copies in a row, a grid or a circle, so a 75 mm VESA square is one hole and one grid. Cut makes a slot where the bracket needs adjustment.
3

Check the render

A hand edit rebuilds in your browser in a few seconds; with the AI, the first render usually appears within a minute or two: a new part gets deeper reasoning through the geometry, and small edits land in seconds. Tap two holes with Measure to read their spacing, and check the plate's thickness behind each screw head.
4

Download and print

A plate shaped by hand downloads free as STL or 3MF; a bracket with AI work in it downloads free on any plan, or for 4 credits without one. G-code comes sliced with the official OrcaSlicer profile of one of 380+ printers.

What one bracket costs

StepCost
Live demo: 3 AI edits of a real part, no accountFree
The plate shape, its sizes typed in the viewer, screw holes with heads, copies, slots and rounded corners by handFree, and the STL or 3MF downloads free
Describing the bracket (one AI request)4 credits on a plan, 3 credits without one
Each small change by chat2 credits; the first 3 of each part free on a plan
Each design change by chat3 credits
Each quick edit by chat (a changed size or number)1 credit
Typing a new number in the dimensions panel, undoFree
STL or 3MF download of a part with AI work in itIncluded in every plan; 4 credits without one, small fixes after it re-downloading free
G-code sliced for your printerThe price of the STL or 3MF download
Maker$7.99 a month: 50 credits a month, about 8 parts with a small change and a few quick edits each, downloads included; cancel anytime
Pro$14.99 a month: 200 credits a month, downloads included
Unlimited$79.99 a month: 300 AI requests a month and unlimited downloads

Bracket descriptions that render right the first time

What it holds, where it mounts, the screws, the spacing. Each opens in the editor with the text already typed; measure your own hardware before printing.

“A wall bracket that holds a 32 mm pipe 20 mm from the wall, a clip opening of 28 mm, two countersunk holes for 4 mm wood screws 40 mm apart, 4 mm walls, rounded edges.”

Open this prompt in the editor

“An L-bracket 40 x 40 mm, 30 mm wide and 4 mm thick, with a 6 mm fillet and a triangular gusset in the inside corner, two M4 countersunk holes on each leg, printed on its side.”

Open this prompt in the editor

“An under-desk mount for a 210 x 120 x 35 mm power strip: two hooks that cradle it, 3 mm walls, two countersunk holes for 4 mm wood screws on each hook, 2 mm clearance around the strip.”

Open this prompt in the editor

“A wall mount for a 160 mm long router 30 mm thick with two keyhole slots 100 mm apart on its back: two pegs 4 mm across and 6 mm long, 100 mm apart, on a plate 140 x 40 x 5 mm with three countersunk screw holes.”

Open this prompt in the editor

Two ways to make the bracket

  • By hand, free. Start from the plate shape and type its size and thickness in the viewer. Drill the screw holes with Hole (M2 to M8 presets, countersink or counterbore), copy them with Duplicate in a row, a grid or a circle, cut adjustment slots with Cut, add a locating peg with Add, round the corners. An adapter plate between two hole patterns, a mounting plate for a board or a cover plate is done this way, and a plate shaped only by hand downloads free as STL or 3MF from a free account. The hole guide shows the steps.
  • With the AI. Describe what it holds and where it mounts: an L-bracket with a gusset, a shelf bracket, a pipe or rod clamp, a hook, a mount shaped to a device. The AI writes it as a parametric model, adds the fillet in the inside corner and thickens the base under the screws.

Hole patterns and screws to start from

Measure your own hardware: clones and revisions move holes.

Pattern or screwNumbers (mm)Ask for
VESA 75 / VESA 10075 x 75 / 100 x 100 square, M4 screws4.5 mm holes on the square
M3 screw, flat head3.4 mm hole, 6.6 mm countersinkthe M3 preset with Countersink
M3 screw, socket head3.4 mm hole, 6.5 x 3.4 mm counterborethe M3 preset with Counterbore
M4 / M5 screw4.5 / 5.5 mm clearance holethe M4 / M5 preset
2020 aluminium extrusion20 mm profile, 6 mm slot, M5 T-nuts5.5 mm holes on a 20 mm pitch
35 mm DIN rail35 mm rail, 7.5 mm deepa DIN clip, by AI

The countersink and counterbore guide has the M2 to M8 table, and Duplicate shows a row, a grid and a bolt circle.

Strength: what makes a printed bracket hold

  • Print it so the load runs along the layers. An L-bracket printed on its side, both legs flat on the bed, is much stronger than one printed standing up, where the load pulls the layers apart.
  • A fillet and a gusset in the inside corner, and 4 or more perimeters in the slicer; ask the AI for "heavy duty" and it thickens the part and adds ribs.
  • Thicker under the screw heads, and a countersink only where the plate is thick enough to keep material under it.

SpeakCAD is the only AI 3D editor that calibrates itself to your printer: Fit Check cuts a five-minute test slice from the part that must fit, you report too tight, perfect or too loose, and every model after that is built with the clearance your printer needs. For a clamp or a clip, the test slice is the part that grips, printed in a few minutes before the whole bracket.

Ready-made, or something else?

What it costs

A plate made by hand from the plate shape downloads free. A bracket with AI work in it uses credits. Start with Maker: 50 credits a month for $7.99, cancel anytime. Shaping a part by hand (a hole and its screw head, a cut, an added tab, raised or engraved text, an extruded face, rounded corners, and copies in a row, a grid or a circle), turning it around in 3D and changing its numbers in the viewer are free, and so is downloading a part you shaped by hand or a ready-made library model; an AI request spends credits for the work it takes, whichever model answers: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits (a big rework of a large model or a very long description takes the most, a web lookup of a product's real measurements counts as part of the work), and each answer shows what it spent; on a plan the first three small changes of each part spend nothing, and an account's very first part spends 2; an answer that changes nothing or only the part's numbers, a request that fails or whose program does not compile, and the first Redo of an answer that missed spend nothing; downloads are included in every plan, and without a plan a download of a part with AI work in it spends 4 credits (small fixes after a download re-download free); G-code sliced for your printer costs the same as the STL or 3MF.

Questions

For a standard bracket in a standard size, a template with sliders or a library model is enough. For a bracket built around your screws, your hole spacing and what it holds, SpeakCAD works from the numbers you give: a flat plate with screw holes by hand, free, or any bracket, clamp or mount described to the AI. It downloads STL, 3MF or G-code sliced for 380+ printers, on a phone or a computer.

Yes: describe the legs, the width, the thickness and the screw holes on each leg, and ask for a fillet or a gusset in the inside corner (one AI request, 4 credits on a plan, 3 without one). Print it on its side so the load runs along the layers.

Yes, by hand. Start from the plate, type its size and thickness, drill one hole of each pattern with its screw preset and head, and Duplicate each into a grid with the pattern's spacing. Put the countersinks of one pattern on the other face. A plate shaped only by hand downloads free.

Yes. The Hole tool has M2 to M8 clearance presets, a tap toggle for the hole a screw cuts its own thread in, and a Countersink (flat head) or Counterbore (socket head) sized by the preset. The AI uses the same standard sizes and can add pockets for heat-set inserts.

Strong enough for most household loads when it is printed in the right direction, with 4 or more perimeters, a fillet or gusset in the inside corner and enough material under the screws. PETG or ASA hold better than PLA in a warm place or outdoors. For anything overhead or safety-critical, use a metal bracket.

Yes. SpeakCAD runs in Safari on iPhone and iPad and in Chrome on Android: type the sizes, tap where the holes go, and the STL, 3MF or G-code lands in Files or Downloads.

A plate shaped by hand from the plate shape, its download included, is free with a free account. With the AI, describing the bracket is one request (4 credits on a plan, 3 without one), its first 3 small changes free on a plan, then each small change by chat 2 credits (1 credit for a quick edit, a changed size or number), and the download is included in every plan (4 credits without one); typing a number in the viewer spends nothing. A new free account also gets its first AI part free (not offered in every country): some accounts get the credits right away, others confirm with a card first (a free trial, nothing charged that day); downloading the part spends 4 credits without a plan, like any AI work (every plan includes downloads). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it.

Give it the screws and the spacing. Print the bracket.

Start from the plate shape for free, or describe the bracket to the AI.