1
Brackets & mounts
SP Connect handlebar clamp for 22.2 to 28.6 mm bars
This is not a fixed STL. SpeakCAD generates the sp connect handlebar clamp for 22.2 to 28.6 mm bars to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a motorcycle bar clamp for 22.2, 25.4 and 28.6 mm bars, two M5 bolts, TPU shims, 40×40 mm flat top pad for an SP Connect head.
What a sp connect handlebar clamp for 22.2 to 28.6 mm bars is
A two-piece handlebar clamp for 22.2 mm (7/8 inch), 25.4 mm (1 inch) and 28.6 mm fat motorcycle bars, with a 40 × 40 mm flat top pad drilled so a store-bought SP Connect mount head can bolt on. It closes with two M5 bolts and nyloc nuts, and swappable TPU shims take up the size difference. Print the halves flat in PETG or ASA with 5 walls.
Check the screw spacing of your SP Connect head against the pad before printing; tell the chat if it differs. Open the ready-made clamp in SpeakCAD for free, adjust any millimetre in the viewer, then download the STL.
People also search
sp connect handlebar mountsp connect motorcycle clamp stlsp connect 22mm mount 3d printsp connect bar mount
Questions people ask about a sp connect handlebar clamp for 22.2 to 28.6 mm bars
A two-piece handlebar clamp for 22.2 mm (7/8 inch), 25.4 mm (1 inch) and 28.6 mm fat motorcycle bars, with a 40 × 40 mm flat top pad drilled so a store-bought SP Connect mount head can bolt on. It closes with two M5 bolts and nyloc nuts, and swappable TPU shims take up the size difference. Print the halves flat in PETG or ASA with 5 walls.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a motorcycle bar clamp for 22.2, 25.4 and 28.6 mm bars, two M5 bolts, TPU shims, 40×40 mm flat top pad for an SP Connect head.
Check the screw spacing of your SP Connect head against the pad before printing; tell the chat if it differs. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More brackets & mounts
Milwaukee M12 FUEL installation-driver holsterA holster that hangs an M12 FUEL installation driver (about 280 mm long) by the barrel so the offset head stays clear.Bambu Lab P1P enclosure panel clipA clip set for closing up an open P1P with 3 mm acrylic or polycarbonate side panels, so it can hold heat for PETG and ASA.Hammerhead Karoo 3 stem cap mountA stem top cap with a Garmin-style quarter-turn tab that holds a Hammerhead Karoo 3, which uses the same quarter-turn interface, above a 1 1/8 inch (28.6 mm)…Ceiling mount ring for a round access pointA ring-shaped mounting plate for disc-style wireless access points that ship without a suitable ceiling bracket, or whose original plate was lost.Philips Hue dimmer switch magnetic wall plateA replacement wall plate for the Philips Hue dimmer switch, a remote about 115 x 35 mm that normally clicks onto a stock plate.Pixel 10 Pro XL out-front bike mountAn out-front handlebar mount for a Pixel 10 Pro XL (about 163 × 77 × 8.6 mm) with a 22.2 / 31.8 mm clamp and a 70 mm deep cradle that clears the Camera Bar.