1
Organizers & storage
Joy-Con 2 desk organizer for four pairs
This is not a fixed STL. SpeakCAD generates the joy-con 2 desk organizer for four pairs to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a Joy-Con 2 organizer, 170×60×35 mm block, eight 34×17 mm slots 30 mm deep in pairs, 2 mm dividers, rear cable channel.
What a joy-con 2 desk organizer for four pairs is
An upright organizer for eight Joy-Con 2 controllers (each about 116 mm long, 32 mm wide and 14 mm thick at the rail). Eight 34 × 17 mm slots are 30 mm deep, grouped in coloured pairs, with a rear channel for the charging grip cable. The block is 170 × 60 × 35 mm with 2 mm dividers. Print in PLA flat on its base.
Original Joy-Con are shorter at about 102 mm and use a slide rail, so they sit lower in these slots. Open the organizer in SpeakCAD at no cost, edit the slot count in the chat or the viewer, then download the STL.
People also search
joy-con 2 holder stlswitch 2 joy con organizer 3d printjoy-con 2 standjoy con 2 storage 3d model
Questions people ask about a joy-con 2 desk organizer for four pairs
An upright organizer for eight Joy-Con 2 controllers (each about 116 mm long, 32 mm wide and 14 mm thick at the rail). Eight 34 × 17 mm slots are 30 mm deep, grouped in coloured pairs, with a rear channel for the charging grip cable. The block is 170 × 60 × 35 mm with 2 mm dividers. Print in PLA flat on its base.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a Joy-Con 2 organizer, 170×60×35 mm block, eight 34×17 mm slots 30 mm deep in pairs, 2 mm dividers, rear cable channel.
Original Joy-Con are shorter at about 102 mm and use a slide rail, so they sit lower in these slots. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More organizers & storage
Festool Systainer insert for Domino cutters and drill bitsA foam-free insert that sits in the bottom of a Festool Systainer SYS3 M 137 and keeps Domino DF 500 cutters, spare bits and the wrench in fixed pockets.Bambu Lab H2D build-plate wall rackA wall rack that stores three H2D / 350 mm class build plates on 8 mm lips with 6 mm gaps so the textured side does not scratch.Dyson Big+Quiet Formaldehyde remote cradleA cradle that holds the larger Big+Quiet Formaldehyde remote (about 130 × 50 × 14 mm) on the top of the cylinder so it does not slide off the curved lid.Bambu Lab AMS side stand with drawerA stand that holds an AMS (372 × 280 × 227 mm) beside the printer at about the height of the lid, with a pull-out drawer for nozzles, glue and the scraper.IKEA SKADIS metric hex key holder, 1.5 to 10 mmA SKADIS block for a full metric L-key set: 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10 mm.Router bit block for 8 mm and 6 mm shanksA stepped router bit block for European trim router bits with 8 mm and 6 mm shanks.