1
Hobby & gaming
Xbox Series X side controller and headset hook
This is not a fixed STL. SpeakCAD generates the xbox series x side controller and headset hook to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Model a stick-on side hook for Xbox Series X, 120×60×4 mm plate, 36 mm controller tongue, 45 mm rounded headset arm, 3 mm walls.
What a xbox series x side controller and headset hook is
A tape-on hook for the side of an Xbox Series X (151 mm wide sides) that holds one controller on a 36 mm tongue and a headset on a 45 mm rounded arm below it. The 120 × 60 mm plate takes 3M VHB tape, stays 10 mm below the top vent and is only 4 mm thick. Print on its side in PETG, 3 mm walls.
On a Series S the 63.5 mm top edge is too narrow for this plate, so use a desk hanger instead. Open the hook in SpeakCAD without paying, edit it in the chat or the viewer, then download the STL.
People also search
xbox series x controller holder stlxbox side headset hook 3d printxbox series x controller hookxbox series x accessory mount
Questions people ask about a xbox series x side controller and headset hook
A tape-on hook for the side of an Xbox Series X (151 mm wide sides) that holds one controller on a 36 mm tongue and a headset on a 45 mm rounded arm below it. The 120 × 60 mm plate takes 3M VHB tape, stays 10 mm below the top vent and is only 4 mm thick. Print on its side in PETG, 3 mm walls.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Model a stick-on side hook for Xbox Series X, 120×60×4 mm plate, 36 mm controller tongue, 45 mm rounded headset arm, 3 mm walls.
On a Series S the 63.5 mm top edge is too narrow for this plate, so use a desk hanger instead. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More hobby & gaming
RC car shock tower braceA shock tower brace spans the two upper shock mounts and stops the towers flexing or snapping during hard landings.LEGO minifigure display shelf for 24 figuresA stepped, wall-hanging shelf with four tiers of six LEGO minifigures each, every figure standing on a pair of real 4.8 mm studs at the 8 mm LEGO pitch so it…LeapFrog LeapReader pen standA stand that parks a LeapReader pen in a 14 mm well with a 40 mm book rest.Strymon Iridium pedalboard riserA 15 mm riser for an Iridium so the jacks clear a packed board, 110 × 70 mm.Lenovo Legion Go S desk standA desk stand for the Lenovo Legion Go S (about 300 × 128 mm, 22.6 mm at the body and about 44 mm deep at the grips) that tilts it back 60 degrees on a 46 mm…Mooer micro pedal double riserA riser that holds two Mooer micro pedals (93.5 × 42 × 52 mm each) side by side and 18 mm higher than the row in front.