LED strip clip for 8 mm slot profile
A snap-in clip that holds a 10 mm wide LED strip along a 40 series aluminium profile, tilted 45 degrees so the light washes across the sim rig instead of into your eyes. The split 7.8 mm key presses into the 8 mm slot and its barbs catch under the slot lip, so there is no T-nut and no adhesive on the profile. It is one cross-section 12 mm long with 1.5 mm walls, thin enough for the lips to spring over the strip. Print a dozen standing on end in PETG, without supports. Describe your measurements and SpeakCAD builds it with AI (credits), then download STL, 3MF or sliced G-code.No ready-made model for this part yet
Sign in and SpeakCAD builds it from the prompt below (4 credits for the part on a plan, its first 3 small changes free; Maker: 50 credits a month for $7.99, cancel anytime). Want to try the editor first? The live demo is free, no account.Adjust
Change its numbers in the viewer for free, or ask the AI for a change in the chat (2 credits for a small change, 1 for a quick edit, 3 for a redesign; the first 3 small changes are free on a plan).Example prompt
Make a snap-in clip that holds a 10 mm wide LED strip on a 40 series aluminium profile with an 8 mm slot. One constant cross-section extruded 12 mm along the slot. Key: 7.8 mm wide and 6 mm deep, split by a 2 mm relief slot, with 0.6 mm barbs whose shoulders sit 4.7 mm below the profile face to catch under a 4.5 mm slot lip. Above it a pad 14 mm wide and 2 mm thick, carrying a channel tilted 45 degrees: 10.4 mm inside width, 1.6 mm floor, side walls 1.5 mm thick and 3 mm tall with 0.8 mm inward lips that hold the strip. Print standing on the cross-section, no supports.
Fit notes
Two numbers decide whether a clip like this holds: the strip width (8, 10 or 12 mm) and the thickness of the slot lip, which is about 4.5 mm on most 40 series profile but varies between makers. A shared file guesses both. In SpeakCAD you type them, along with the tilt, and print one clip to check the snap before making the set.
Questions people ask about an LED strip clip for 8 mm slot profile
A snap-in clip that holds a 10 mm wide LED strip along a 40 series aluminium profile, tilted 45 degrees so the light washes across the sim rig instead of into your eyes. The split 7.8 mm key presses into the 8 mm slot and its barbs catch under the slot lip, so there is no T-nut and no adhesive on the profile. It is one cross-section 12 mm long with 1.5 mm walls, thin enough for the lips to spring over the strip. Print a dozen standing on end in PETG, without supports.
There is no ready-made model for this part yet. Click Build it with AI and sign in: the example prompt on this page is filled in, and SpeakCAD builds the part from it in your browser (4 credits for the part on a plan, its first 3 small changes free). Change any number in the viewer for free, then download a watertight STL or 3MF, included in every plan (4 credits without one), or G-code sliced for your printer at the same price. Start with Maker: 50 credits a month for $7.99, cancel anytime.
SpeakCAD builds it to your measurements from the example prompt on this page: the part uses 4 credits on a plan, its first 3 small changes free (3 without a plan), and a small change after them 2, then the STL or 3MF download is included in every plan (4 credits without one), or G-code sliced for your printer at the same price. Start with Maker: 50 credits a month for $7.99, cancel anytime. To try the editor before paying, the live demo is free, no account.
A shared STL is modelled for someone else's measurements. SpeakCAD builds this part to the millimetres you give it (AI requests use credits), so the file you download is sized for the part you actually own.
Yes. SpeakCAD slices the part on its servers with OrcaSlicer and your printer's official profile (380+ printers, including Bambu Lab, Prusa, Creality and Elegoo), and you download the G-code (a sliced .gcode.3mf for Bambu Lab printers). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it. Pick your printer on the printers page to see its profile.
No. SpeakCAD runs in the browser on your phone or computer: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL, 3MF or sliced G-code.