Pegboard rack for quarter-sheet sandpaper
A sandpaper rack for quarter sheets (4.5 × 5.5 inch, about 114 × 140 mm) sorted by grit. Six pockets 120 × 12 mm deep enough for 25 sheets each sit in a stepped front, with grit labels on the lip and a finger notch in each pocket. Pegs for 1/4 inch pegboard holes on 25.4 mm centres hold it up. Print upright in PLA. Describe your measurements and SpeakCAD builds it with AI (credits), then download STL, 3MF or sliced G-code.No ready-made model for this part yet
Sign in and SpeakCAD builds it from the prompt below (4 credits for the part on a plan, its first 3 small changes free; Maker: 50 credits a month for $7.99, cancel anytime). Want to try the editor first? The live demo is free, no account.Adjust
Change its numbers in the viewer for free, or ask the AI for a change in the chat (2 credits for a small change, 1 for a quick edit, 3 for a redesign; the first 3 small changes are free on a plan).Example prompt
Design a pegboard sandpaper rack, six stepped 120×12 mm pockets 90 mm deep, grit label lips, finger notches, 6 mm pegs 25.4 mm apart.
Fit notes
Third sheets are 93 mm wide and will fall over in these pockets; tell the chat to narrow them.
Questions people ask about a pegboard rack for quarter-sheet sandpaper
A sandpaper rack for quarter sheets (4.5 × 5.5 inch, about 114 × 140 mm) sorted by grit. Six pockets 120 × 12 mm deep enough for 25 sheets each sit in a stepped front, with grit labels on the lip and a finger notch in each pocket. Pegs for 1/4 inch pegboard holes on 25.4 mm centres hold it up. Print upright in PLA.
There is no ready-made model for this part yet. Click Build it with AI and sign in: the example prompt on this page is filled in, and SpeakCAD builds the part from it in your browser (4 credits for the part on a plan, its first 3 small changes free). Change any number in the viewer for free, then download a watertight STL or 3MF, included in every plan (4 credits without one), or G-code sliced for your printer at the same price. Start with Maker: 50 credits a month for $7.99, cancel anytime.
SpeakCAD builds it to your measurements from the example prompt on this page: the part uses 4 credits on a plan, its first 3 small changes free (3 without a plan), and a small change after them 2, then the STL or 3MF download is included in every plan (4 credits without one), or G-code sliced for your printer at the same price. Start with Maker: 50 credits a month for $7.99, cancel anytime. To try the editor before paying, the live demo is free, no account.
A shared STL is modelled for someone else's measurements. SpeakCAD builds this part to the millimetres you give it (AI requests use credits), so the file you download is sized for the part you actually own.
Yes. SpeakCAD slices the part on its servers with OrcaSlicer and your printer's official profile (380+ printers, including Bambu Lab, Prusa, Creality and Elegoo), and you download the G-code (a sliced .gcode.3mf for Bambu Lab printers). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it. Pick your printer on the printers page to see its profile.
No. SpeakCAD runs in the browser on your phone or computer: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL, 3MF or sliced G-code.