1
Brackets & mounts
HC-SR04 ultrasonic sensor mount
This is not a fixed STL. SpeakCAD generates the hc-sr04 ultrasonic sensor mount to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create an HC-SR04 mount, two 16.4 mm holes at 26 mm centres, 45.6×20.6 mm board pocket, pin slot, M3 tilt base 0–30 degrees.
What a hc-sr04 ultrasonic sensor mount is
A mount for an HC-SR04 ultrasonic sensor (45 × 20 mm, two 16 mm transducers). The front plate has two 16.4 mm holes at 26 mm centres, a 45.6 × 20.6 mm board pocket and a 10 × 3 mm slot for the pins, and the base tilts from 0 to 30 degrees on an M3 bolt. Walls are 2 mm. Print the plate face-down in PLA.
The waterproof JSN-SR04T has a single probe on a cable, so this mount does not fit it. Open the ready-made model in SpeakCAD for free, adjust any millimetre, then download the STL.
People also search
hc-sr04 mount stlultrasonic sensor holder 3d printhc-sr04 brackethc-sr04 case 3d model
Questions people ask about a hc-sr04 ultrasonic sensor mount
A mount for an HC-SR04 ultrasonic sensor (45 × 20 mm, two 16 mm transducers). The front plate has two 16.4 mm holes at 26 mm centres, a 45.6 × 20.6 mm board pocket and a 10 × 3 mm slot for the pins, and the base tilts from 0 to 30 degrees on an M3 bolt. Walls are 2 mm. Print the plate face-down in PLA.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create an HC-SR04 mount, two 16.4 mm holes at 26 mm centres, 45.6×20.6 mm board pocket, pin slot, M3 tilt base 0–30 degrees.
The waterproof JSN-SR04T has a single probe on a cable, so this mount does not fit it. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More brackets & mounts
Sonos Era 300 wall bracket with cable channelA bracket that holds an Era 300 (about 260 mm wide) 40 mm off the wall with a 10 mm cable channel.Milwaukee M18 FUEL impact wall holsterA holster that parks an M18 FUEL impact (about 140 mm long without battery) on a 4.5 mm hole pair so the tool is not on the bench.Google Nest Hub 2nd gen wall mountA wall mount for a Google Nest Hub 2nd gen (about 177 × 120 × 69 mm) that grips the fabric base, so the screen sits at eye level next to a light switch.Wall mount for 18 V power tool batteriesA wall rail that spare 18 V slide-on battery packs click onto, so they stop rolling around a drawer and are visible when you need one.Shimano Di2 junction box holder for 31.8 mm handlebarThe Shimano SM-EW90 Di2 junction A normally hangs under the stem on a rubber band, where it rattles and gets pulled by the bar bag straps.IKEA Ribba frame tabletop stand for 21 x 30 cmA pair of feet that lets a wall-only IKEA Ribba frame stand on a desk or shelf, since Ribba frames come without a back easel.