1
Hobby & gaming
Teenage Engineering Pocket Operator stand
This is not a fixed STL. SpeakCAD generates the teenage engineering pocket operator stand to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create a 30° stand for a Pocket Operator, 108×16 mm ledge with 2 mm lip, battery cutout in the back rest, 110×70 mm base.
What a teenage engineering pocket operator stand is
A desk stand that holds a Teenage Engineering Pocket Operator (about 106 × 60 mm) at 30° so the screen and buttons face you. The bottom edge sits in a 108 × 16 mm ledge with a 2 mm lip, the back rest has a cutout for the two AAA batteries, and the 110 × 70 mm base leaves the 3.5 mm jacks on top free. Print on its side in PLA.
The official silicone PO cases add a few millimetres, so tell the chat if you keep yours in one. Open the ready-made model in SpeakCAD for free, change the angle in the viewer or the chat, then download the STL.
People also search
pocket operator stand stlteenage engineering pocket operator stand 3d printpo-33 standpocket operator holder
Questions people ask about a teenage engineering pocket operator stand
A desk stand that holds a Teenage Engineering Pocket Operator (about 106 × 60 mm) at 30° so the screen and buttons face you. The bottom edge sits in a 108 × 16 mm ledge with a 2 mm lip, the back rest has a cutout for the two AAA batteries, and the 110 × 70 mm base leaves the 3.5 mm jacks on top free. Print on its side in PLA.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create a 30° stand for a Pocket Operator, 108×16 mm ledge with 2 mm lip, battery cutout in the back rest, 110×70 mm base.
The official silicone PO cases add a few millimetres, so tell the chat if you keep yours in one. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More hobby & gaming
PS5 DualSense dual controller charging standA twin-bay stand for two PlayStation 5 DualSense or DualSense Edge controllers (160 x 66 x 106 mm) that holds them face-out with their USB-C ports aligned ov…Meta Quest 3S Elite strap wall dockA wall dock that holds a Quest 3S with the Elite battery strap hanging on a 40 mm hook and the headset sitting in a 180 mm wide cradle.AYANEO KUN travel standA folding stand that holds an AYANEO KUN at 50 degrees with a 14 mm USB-C slot, two pieces on a 6 mm pin.DualSense single wall hook with cable slotA single hook that holds one DualSense (160 × 66 × 106 mm) face out with its USB-C cable plugged in.Sim rig aluminium profile phone mountA phone mount for a 40 series aluminium profile sim rig (40 × 40 or 40 × 80 mm with an 8 mm slot) that bolts into the slot with an M6 bolt and T-nut and hold…Magnetic miniature movement trayA movement tray lets you slide a whole unit of miniatures across the board in one motion.