Enclosures & cases

Sim pedal controller box with three GX12 sockets

A controller box for DIY sim pedals with three GX12 sockets on one side, one per pedal, and an Arduino Pro Micro inside. The sockets fit 12.2 mm holes on a 25 mm pitch, the 33 × 18 mm board rests in a ledge cradle with its USB port at a 13 × 8 mm opening, and the lid closes with four M3 screws into heat-set inserts. An ear at each end takes an M8 bolt for a 40 series aluminium profile. Walls, floor and lid are 2 mm. Print the body open side up and the lid flat, without supports. Describe your measurements and SpeakCAD builds it with AI (credits), then download STL, 3MF or sliced G-code.
No ready-made model yet: building it uses credits (4 credits for the part on a plan, its first 3 small changes free; Maker: 50 credits a month for $7.99, cancel anytime).Updated

No ready-made model for this part yet

Sign in and SpeakCAD builds it from the prompt below (4 credits for the part on a plan, its first 3 small changes free; Maker: 50 credits a month for $7.99, cancel anytime). Want to try the editor first? The live demo is free, no account.
1

Describe

Sign in: the example prompt below is filled in. SpeakCAD builds the part from it with AI, 4 credits for the part on a plan, its first 3 small changes free (Maker: 50 credits a month for $7.99, cancel anytime). Replace any number with what you measured first.
2

Adjust

Change its numbers in the viewer for free, or ask the AI for a change in the chat (2 credits for a small change, 1 for a quick edit, 3 for a redesign; the first 3 small changes are free on a plan).
3

Print

Download a watertight STL or 3MF, included in every plan (4 credits without one), or G-code sliced for your printer at the same price.

Example prompt

Design a controller box for DIY sim pedals with three GX12 sockets and an Arduino Pro Micro inside. Body 90 × 60 × 30 mm outside, 2 mm walls and floor. In one long wall, three 12.2 mm holes on a 25 mm pitch, centred 15 mm above the base. For the 33 × 18 mm board, a cradle of ledges 1.6 mm wide and 3 mm above the floor, 33.4 × 18.4 mm inside, 9 mm from the opposite long wall, with the USB end at a short wall that has a 13 × 8 mm opening centred 8 mm above the base. Four corner posts 7 mm square with 4 mm holes 6 mm deep for M3 heat-set inserts. Lid 90 × 60 × 2 mm with a 1.5 mm lip and four 3.4 mm holes. An ear on each short end, 20 × 30 × 4 mm, flush with the base, with an 8.4 mm hole for an M8 bolt. Print body open side up, lid flat, no supports.

Build it with AI opens the app with this prompt already typed. Replace any number with what you measured before sending it; the rest of the design stays consistent.

Fit notes

Every pedal build is wired differently. A load cell amplifier board needs its own space, GX16 sockets need 16 mm holes on a wider pitch, and a handbrake adds a fourth socket. In SpeakCAD you say how many sockets, which board and where the cable leaves, and the box grows to suit.

Also searched as: sim pedal controller box stl, gx12 pro micro enclosure 3d print, diy sim pedals electronics case, load cell pedal controller box.

Questions people ask about a sim pedal controller box with three GX12 sockets

A controller box for DIY sim pedals with three GX12 sockets on one side, one per pedal, and an Arduino Pro Micro inside. The sockets fit 12.2 mm holes on a 25 mm pitch, the 33 × 18 mm board rests in a ledge cradle with its USB port at a 13 × 8 mm opening, and the lid closes with four M3 screws into heat-set inserts. An ear at each end takes an M8 bolt for a 40 series aluminium profile. Walls, floor and lid are 2 mm. Print the body open side up and the lid flat, without supports.

There is no ready-made model for this part yet. Click Build it with AI and sign in: the example prompt on this page is filled in, and SpeakCAD builds the part from it in your browser (4 credits for the part on a plan, its first 3 small changes free). Change any number in the viewer for free, then download a watertight STL or 3MF, included in every plan (4 credits without one), or G-code sliced for your printer at the same price. Start with Maker: 50 credits a month for $7.99, cancel anytime.

SpeakCAD builds it to your measurements from the example prompt on this page: the part uses 4 credits on a plan, its first 3 small changes free (3 without a plan), and a small change after them 2, then the STL or 3MF download is included in every plan (4 credits without one), or G-code sliced for your printer at the same price. Start with Maker: 50 credits a month for $7.99, cancel anytime. To try the editor before paying, the live demo is free, no account.

A shared STL is modelled for someone else's measurements. SpeakCAD builds this part to the millimetres you give it (AI requests use credits), so the file you download is sized for the part you actually own.

Yes. SpeakCAD slices the part on its servers with OrcaSlicer and your printer's official profile (380+ printers, including Bambu Lab, Prusa, Creality and Elegoo), and you download the G-code (a sliced .gcode.3mf for Bambu Lab printers). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it. Pick your printer on the printers page to see its profile.

No. SpeakCAD runs in the browser on your phone or computer: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL, 3MF or sliced G-code.

Build, adjust and print your sim pedal controller box with three GX12 sockets

Nothing to install. The prompt is waiting in the app after you sign in: SpeakCAD builds the part with AI (credits), no CAD skills needed, you check the fit, then download the STL, 3MF or sliced G-code.

Looking for a finished design by a maker? Browse the enclosures & cases on the marketplace, where makers share their models, most of them free.