1
Brackets & mounts
Precision Bass wall hanger
This is not a fixed STL. SpeakCAD generates the precision bass wall hanger to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Model a bass guitar wall hanger, 50 mm yoke opening, 70 mm arms 16 mm thick angled 10° up, 120×60 mm back plate with three 5 mm screw holes.
What a precision bass wall hanger is
A wall hanger sized for a Fender Precision Bass and similar 4-string basses (44.5 mm nut width, heavy headstock). The yoke opening is 50 mm, the arms are 70 mm long, 16 mm thick and angled 10° up, and a 120 × 60 mm back plate takes three 5 mm screws into a stud or plug. Pad the arms with felt. Print on its side in PETG at 50% infill.
Five-string basses often have 45 to 48 mm nuts and wider headstocks; ask the chat for a 55 mm opening. Open the ready-made model in SpeakCAD for free, adjust any millimetre in the viewer or the chat, then download the STL.
People also search
bass guitar wall hanger stlprecision bass wall mount 3d printbass hanger 3d modelp bass wall hanger
Questions people ask about a precision bass wall hanger
A wall hanger sized for a Fender Precision Bass and similar 4-string basses (44.5 mm nut width, heavy headstock). The yoke opening is 50 mm, the arms are 70 mm long, 16 mm thick and angled 10° up, and a 120 × 60 mm back plate takes three 5 mm screws into a stud or plug. Pad the arms with felt. Print on its side in PETG at 50% infill.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Model a bass guitar wall hanger, 50 mm yoke opening, 70 mm arms 16 mm thick angled 10° up, 120×60 mm back plate with three 5 mm screw holes.
Five-string basses often have 45 to 48 mm nuts and wider headstocks; ask the chat for a 55 mm opening. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More brackets & mounts
28BYJ-48 stepper motor mountA mount for a 28BYJ-48 stepper (28 mm body, flange holes 35 mm apart, 5 mm D-flat shaft offset 8 mm from the centre).Rivian R1S cup holder phone mountA phone mount that twists into an R1S front cup holder and holds a phone 70 to 80 mm wide up beside the 15.6 inch centre screen.Sony A6700 Arca-Swiss plateA short Arca-Swiss plate for the Sony A6700 (122 × 69 × 75.1 mm).iPad mini car headrest mount for back seatA rear-seat holder for the iPad mini (195.4 x 134.8 x 6.3 mm) that clamps to the two headrest posts so children can watch films in landscape.Tesla NACS mobile connector wall holster and cable hookA holster for the Tesla NACS plug on the Mobile Connector or Wall Connector, with a separate hook for the 6 m cable and a shelf for the control box.UniFi G6 Instant corner mountA corner mount that aims a G6 Instant at 45 degrees across a porch, 80 × 40 × 40 mm with the official 4-hole pattern.