1
The prompt on this page opens in SpeakCAD already filled in — after sign-in too. The model renders in your browser. Preview is free.Desk & office
MacBook Air 15-inch M4 clamshell stand
This is not a fixed STL. SpeakCAD generates the macbook air 15-inch m4 clamshell stand to your millimetres, you adjust it in the chat, then you download and print it.2
Change any millimetre in the chat: wall thickness, hole size, the thing it clips onto. Iterations stay in the tab until it matches what you own.Adjust
3Print
Download a watertight STL or 3MF for 2 credits, drop it in your slicer, and print it. Small fit fixes re-download free.Get it nowThe example prompt comes with you, even through sign-in. Preview is free; a download costs 2 credits.
What a macbook air 15-inch m4 clamshell stand is
A clamshell stand for a 15-inch MacBook Air M4 (about 11.5 mm closed, 340 mm wide) that lifts the hinge 20 mm so air can exit and a USB-C hub can sit underneath. Four 12 mm posts register the rubber feet, the span is 342 × 240 mm, and a 80 × 20 mm rear cable gap stays open. Print as two PLA halves.
15-inch Air stands copied from the 13-inch leave the extra width hanging. Tell SpeakCAD the foot spacing you measured, preview the stand in the browser without paying, then download the STL.
Example prompt
Model a MacBook Air 15 M4 clamshell stand 342×240×20 mm in two halves, four 12 mm foot posts, 80×20 mm rear cable gap, 2.4 mm walls.
People also search
macbook air 15 m4 stand stl15 inch macbook air clamshell 3d printmacbook air 15 m4 risermacbook air 15 dock 3d model
Questions people ask about a macbook air 15-inch m4 clamshell stand
A clamshell stand for a 15-inch MacBook Air M4 (about 11.5 mm closed, 340 mm wide) that lifts the hinge 20 mm so air can exit and a USB-C hub can sit underneath. Four 12 mm posts register the rubber feet, the span is 342 × 240 mm, and a 80 × 20 mm rear cable gap stays open. Print as two PLA halves.
Click Get it now on this page: the example prompt is filled in for you after you sign in. The model renders in your browser — nothing to install — and previewing is free. Adjust any millimetre in the chat, then export a watertight STL or 3MF for 2 credits when you want to print.
Start from this working example and replace any number with what you measured: Model a MacBook Air 15 M4 clamshell stand 342×240×20 mm in two halves, four 12 mm foot posts, 80×20 mm rear cable gap, 2.4 mm walls.
15-inch Air stands copied from the 13-inch leave the extra width hanging. In SpeakCAD you generate and preview for free, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More desk & office
Garmin Fenix 8 charger cable dockA desk dock that holds a Garmin Fenix 8 (51 mm case) face-out while the official clip charger clamps the back.AKAI MPK Mini Plus standA 12 degree stand for an MPK Mini Plus that clears the extra drum pads, 220 mm span in two halves.Magic Trackpad 2 angled desk wedgeA 8 degree wedge under a Magic Trackpad 2 / USB-C Trackpad (about 160 × 115 mm) so the front edge matches a Magic Keyboard.Dyson Corrale HS07 charger dockA dock that holds a Dyson Corrale HS07 (about 45 × 32 mm closed) on its magnetic charger so the plates do not rest on the glass.Bose Smart Ultra soundbar cable combA comb that sits behind a Smart Ultra soundbar and separates HDMI eARC, power and optical so they do not knot.Mouse bungee with weighted baseA desk accessory that lifts a wired mouse cable off the mat so it never snags or drags.