1
Desk & office
Focusrite Scarlett 2i2 4th Gen angled desk stand
A desk stand that tilts a Focusrite Scarlett 2i2 4th Gen or Scarlett Solo (the 2i2 is 180 x 47.5 x 117 mm) back 25 degrees so the gain halos and Air button face you rather than the ceiling, while leaving the rear XLR combo jacks, monitor outputs and USB-C port accessible. The cradle is 182 mm wide with a 1.5 mm front lip and 0.5 mm clearance, sits on a 120 mm deep base with 10 mm rubber-foot recesses, and has a 40 mm cable pass-through so leads run under the interface instead of round it. A 60 x 20 mm side slot parks a Shure SM7B or Rode PodMic XLR cable when unplugged. Print it on its base with 2 mm walls. Open the ready-made model free, resize it on your phone or computer, then download a print-ready STL, 3MF or G-code sliced for your printer, free.Opening the ready-made model and downloading it as STL or 3MF are free, no card; AI changes use credits, from Maker at $7.99 a month.No printer? We print this part and ship it to your door. See its priceUpdated
2
Adjust
Change its numbers in the viewer for free, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use 2 credits per request (1 for a quick edit, 3 for a redesign), paid with a plan from Maker at $7.99 a month.3Print
Download a watertight STL or 3MF free, with your numbers and hand edits, or G-code sliced for your printer at the same price. After an AI change the download is included in every plan (4 credits without one).
Dimensions of the ready-made model (editable)
| Parameter | Value |
|---|---|
| device width (long side) | 182 mm |
| device depth | 120 mm |
| clearance around device | 0.5 mm |
| wall thickness | 2 mm |
| front retaining lip height | 1.5 mm |
| solid flat base thickness | 5 mm |
| inset from base edges | 15 mm |
| extra margin around platform footprint projection | 20 mm |
| side wall height of the cradle pocket (holds device edge) | 15 mm |
Example prompt
Model an angled stand for a Focusrite Scarlett 2i2 4th Gen: a 182 x 120 mm cradle with 0.5 mm clearance and 1.5 mm front lip tilted 25 degrees, a 40 mm rear cable pass-through, a 60 x 20 mm side XLR cable slot, four 10 mm rubber foot recesses, 2 mm walls and a solid 5 mm base.
Fit notes
A riser for the 3rd Gen does not fit the slightly taller 4th Gen chassis. Tell SpeakCAD your interface generation and tilt angle, preview the stand in the browser, refine in the chat and download the STL.
Questions people ask about a Focusrite Scarlett 2i2 4th Gen angled desk stand
A desk stand that tilts a Focusrite Scarlett 2i2 4th Gen or Scarlett Solo (the 2i2 is 180 x 47.5 x 117 mm) back 25 degrees so the gain halos and Air button face you rather than the ceiling, while leaving the rear XLR combo jacks, monitor outputs and USB-C port accessible. The cradle is 182 mm wide with a 1.5 mm front lip and 0.5 mm clearance, sits on a 120 mm deep base with 10 mm rubber-foot recesses, and has a 40 mm cable pass-through so leads run under the interface instead of round it. A 60 x 20 mm side slot parks a Shure SM7B or Rode PodMic XLR cable when unplugged. Print it on its base with 2 mm walls.
Click Open it free on this page and create a free account (no card): the ready-made model opens in your browser, on your phone or computer, nothing to install. Change its numbers in the viewer for free and download a watertight STL or 3MF free, or G-code sliced for your printer at the same price. An AI change in the chat uses 2 credits per request (3 for a redesign), and the download after it is included in every plan (4 credits without one). Start with Maker: 50 credits a month for $7.99, cancel anytime.
On this page: open the ready-made model free in a SpeakCAD account (no card), change any dimension in the viewer, then download the STL or 3MF free, or G-code sliced for your printer at the same price.
A shared STL is modelled for someone else's measurements. Here you open the ready-made model free, change it to your measurements in the viewer, then download a file sized for the part you actually own, free as STL or 3MF.
Yes. SpeakCAD slices the part on its servers with OrcaSlicer and your printer's official profile (380+ printers, including Bambu Lab, Prusa, Creality and Elegoo), and you download the G-code (a sliced .gcode.3mf for Bambu Lab printers). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it. Pick your printer on the printers page to see its profile.
No. SpeakCAD runs in the browser on your phone or computer: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL, 3MF or sliced G-code.
Print it your way
More desk & office
Logitech Brio webcam clip for thin bezel monitorsReady-made, opens free. A replacement clip for the Logitech Brio 4K webcam that grips a monitor with a bezel under 6 mm, which the stock mount slides off.iPad mini 7 bedside reading standReady-made, opens free. A bedside stand that holds an iPad mini 7 (about 195 × 135 × 6.3 mm) at 40 degrees in portrait with a 14 mm USB-C slot and a 8 mm lip so a Folio case does no…AKAI MPK Mini Plus standReady-made, opens free. A 12 degree stand for an MPK Mini Plus that clears the extra drum pads, 220 mm span in two halves.Mac mini M4 under-monitor shelfReady-made, opens free. A shelf that hides a Mac mini M4 (about 127 × 127 × 50 mm) under a monitor with 20 mm side vents and a 16 mm power/Thunderbolt cutout at the back.Thunderbolt 5 dock MacBook under-standReady-made, opens free. A 30 mm stand that lifts a closed MacBook Air or 14-inch Pro and hides a Thunderbolt 5 dock (about 200 × 80 × 28 mm) underneath so the single cable is the on…Adhesive desk cable clip setReady-made, opens free. A set of low-profile clips that stick to the edge of a desk and hold charging cables.