1
Hobby & gaming
DualSense wall rack for four controllers
This is not a fixed STL. SpeakCAD generates the dualsense wall rack for four controllers to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a wall rack for four DualSense controllers, 700×40×5 mm back plate, four 40 mm arms 55 mm deep with 6 mm lips, 170 mm spacing, 4 mm holes.
What a dualsense wall rack for four controllers is
A wall rack for four PS5 DualSense controllers (160 × 66 × 106 mm) hung by the gap between the grips. Each 40 mm wide arm is 55 mm deep with a 6 mm raised tip so the pad rests on its touchpad edge, arms are 170 mm apart and the 700 × 40 × 5 mm back plate has five 4 mm countersunk holes. Print the arms flat in PETG and slide them into dovetails.
The DualSense Edge has the same shell but back buttons, so leave the arms long enough. Open the ready-made rack in SpeakCAD for free, change any millimetre in the viewer or the chat, then download the STL.
People also search
dualsense wall mount stlps5 controller wall rack 3d printps5 controller wall holderdualsense wall hanger 3d model
Questions people ask about a dualsense wall rack for four controllers
A wall rack for four PS5 DualSense controllers (160 × 66 × 106 mm) hung by the gap between the grips. Each 40 mm wide arm is 55 mm deep with a 6 mm raised tip so the pad rests on its touchpad edge, arms are 170 mm apart and the 700 × 40 × 5 mm back plate has five 4 mm countersunk holes. Print the arms flat in PETG and slide them into dovetails.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a wall rack for four DualSense controllers, 700×40×5 mm back plate, four 40 mm arms 55 mm deep with 6 mm lips, 170 mm spacing, 4 mm holes.
The DualSense Edge has the same shell but back buttons, so leave the arms long enough. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More hobby & gaming
DJI Avata 2 display standA shelf stand that shows off a DJI Avata 2 (185 × 212 × 64 mm) and keeps weight off its landing pads.Board game token tray with scoopsToken trays sort cardboard chits and wooden cubes into compartments with sloped scoop bottoms so you can pick pieces up with a fingertip.Steam Deck OLED dock stand with USB-C cutoutA desk stand that holds a Steam Deck OLED (298 x 117 x 49 mm) at a 15 degree lean while a USB-C hub or the official dock's cable stays plugged into the top p…Steam Deck 2 travel kickstand with case lipA clip-on kickstand for a Steam Deck 2 (about 300 × 120 × 50 mm) that still clips over a Jsaux or dbrand case.ASUS ROG Ally X grip shellA two-part shell that thickens Ally X grips by 8 mm without covering vents or the rear buttons.PS5 detachable disc drive storage sleeveA dust sleeve for the detachable Ultra HD Blu-ray drive sold for the PS5 Slim, Digital Edition and PS5 Pro (the drive is about 185 × 145 × 20 mm, measure you…