1
Everyday fixes
Brompton seatpost AirTag clamp
This is not a fixed STL. SpeakCAD generates the brompton seatpost airtag clamp to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Model a Brompton seatpost AirTag clamp, 31.8 mm band 12 mm tall with M3 screw, 32.5×8.6 mm pocket with 1.2 mm skin, TPU liner, PETG.
What a brompton seatpost airtag clamp is
A low-profile clamp for a Brompton seatpost (31.8 mm) that holds an AirTag (31.9 mm across, 8 mm thick) under the saddle, sitting high enough not to hit the frame when the post is dropped for folding. The pocket is 32.5 × 8.6 mm with a 1.2 mm skin, the band is 12 mm tall and closes with an M3 screw, and a TPU liner protects the post finish. Print on its side in PETG.
The Brompton titanium seatpost is the same diameter, but check the length before mounting low. Open the ready-made clamp in SpeakCAD for free, change any millimetre in the viewer or the chat, then download the STL.
People also search
brompton airtagbrompton airtag mount stlbrompton seatpost airtagbrompton accessories 3d print
Questions people ask about a brompton seatpost airtag clamp
A low-profile clamp for a Brompton seatpost (31.8 mm) that holds an AirTag (31.9 mm across, 8 mm thick) under the saddle, sitting high enough not to hit the frame when the post is dropped for folding. The pocket is 32.5 × 8.6 mm with a 1.2 mm skin, the band is 12 mm tall and closes with an M3 screw, and a TPU liner protects the post finish. Print on its side in PETG.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Model a Brompton seatpost AirTag clamp, 31.8 mm band 12 mm tall with M3 screw, 32.5×8.6 mm pocket with 1.2 mm skin, TPU liner, PETG.
The Brompton titanium seatpost is the same diameter, but check the length before mounting low. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More everyday fixes
Minimalist wallet money clipA slim card wallet with a money clip holds four cards and folded notes in a package barely thicker than the cards themselves.Stokke Tripp Trapp cup holder clip for the side railA clip-on cup holder for the Stokke Tripp Trapp high chair that attaches to the wooden side rail and puts a sippy cup or snack pot within reach of a toddler…Tesla Model Y Juniper console-lid organizerA shallow organizer that sits under a Juniper Model Y console lid for cards and a USB-C dongle, 140 × 70 × 12 mm.Porsche Taycan charge-port holsterA garage holster that parks a Taycan Type 2 or NACS adapter and the charge-port cap so they are not on the floor.10 inch rack 1U cable management panelA 1U cable management panel for a 10 inch rack with four 30 mm D-rings that hold patch leads between a switch and a patch panel.Single-speed chain guide for bottom bracketA chain guide keeps the chain from bouncing off the chainring on single-speed or 1x setups over rough ground.