1
Enclosures & cases
XL4015 buck converter case
This is not a fixed STL. SpeakCAD generates the xl4015 buck converter case to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create an XL4015 buck case, 56×25×22 mm cavity, two M3 standoffs, 5 mm wire holes at both ends, 3 mm trimmer holes, heatsink grille.
What a xl4015 buck converter case is
A vented case for the XL4015 5 A buck converter (about 54 × 23 × 18 mm with its heatsink). The cavity is 56 × 25 × 22 mm with two M3 standoffs, 5 mm wire holes at each end, a 3 mm hole over each trimmer pot and a slot grille over the heatsink. Walls are 1.6 mm. Print upside down in PETG, not PLA, as the heatsink gets warm.
The LM2596 module is smaller at about 43 × 21 mm and sits loose in this case. Open the ready-made model in SpeakCAD for free, change any opening, then download the STL.
People also search
xl4015 case stlxl4015 buck converter enclosurexl4015 housing 3d print5a buck converter case 3d model
Questions people ask about a xl4015 buck converter case
A vented case for the XL4015 5 A buck converter (about 54 × 23 × 18 mm with its heatsink). The cavity is 56 × 25 × 22 mm with two M3 standoffs, 5 mm wire holes at each end, a 3 mm hole over each trimmer pot and a slot grille over the heatsink. Walls are 1.6 mm. Print upside down in PETG, not PLA, as the heatsink gets warm.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create an XL4015 buck case, 56×25×22 mm cavity, two M3 standoffs, 5 mm wire holes at both ends, 3 mm trimmer holes, heatsink grille.
The LM2596 module is smaller at about 43 × 21 mm and sits loose in this case. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More enclosures & cases
Raspberry Pi 5 Hailo HAT caseA case that clears a Pi 5 with the Hailo AI HAT, 30 mm extra height, GPIO slot and 40 mm fan vents.Seeed XIAO ESP32S3 Sense camera caseA case for a Seeed XIAO ESP32S3 Sense (21 × 17.8 mm board with the camera expansion board, about 15 mm tall).L298N motor driver caseA vented case for the red L298N dual motor driver (43 × 43 mm, about 27 mm tall with the heatsink).LD2410C mmWave presence sensor caseA slim case for an HLK-LD2410C radar (22 × 16 mm) paired with an ESP32-C3 SuperMini (22.5 × 18 mm).Bezel case for a 0.96 inch OLED moduleA small front bezel and back cover for the popular 0.96 inch I2C OLED module, turning a bare board into a neat readout you can screw to a panel or stand on a…ESP32-C3 SuperMini case with BME280 sensor ventsA tiny room sensor enclosure for an ESP32-C3 SuperMini board (22.5 x 18 mm) paired with a BME280 breakout (about 15 x 12 mm).