1
The prompt on this page opens in SpeakCAD already filled in — after sign-in too. The model renders in your browser. Preview is free.Tools & jigs
Plane-blade sharpening jig 50 mm
This is not a fixed STL. SpeakCAD generates the plane-blade sharpening jig 50 mm to your millimetres, you adjust it in the chat, then you download and print it.2
Change any millimetre in the chat: wall thickness, hole size, the thing it clips onto. Iterations stay in the tab until it matches what you own.Adjust
3Print
Download a watertight STL or 3MF for 2 credits, drop it in your slicer, and print it. Small fit fixes re-download free.Get it nowThe example prompt comes with you, even through sign-in. Preview is free; a download costs 2 credits.
What a plane-blade sharpening jig 50 mm is
A 50 mm honing jig that holds a plane iron at 25 or 30 degrees with a 4 mm clamp bar. The roller is a 608 bearing you drop in. Print in PETG.
Freehand 25 degrees is a guess. In SpeakCAD you set the iron width, preview the jig in the browser at no cost, then download the STL.
Example prompt
Design a 50 mm plane-iron honing jig with 25 and 30 degree beds, 4 mm clamp bar, 608 bearing pocket, 2 mm PETG walls.
People also search
plane blade honing jig stl50mm sharpening jig 3d printbench plane iron guidehoning jig 25 degree 3d model
Questions people ask about a plane-blade sharpening jig 50 mm
A 50 mm honing jig that holds a plane iron at 25 or 30 degrees with a 4 mm clamp bar. The roller is a 608 bearing you drop in. Print in PETG.
Click Get it now on this page: the example prompt is filled in for you after you sign in. The model renders in your browser — nothing to install — and previewing is free. Adjust any millimetre in the chat, then export a watertight STL or 3MF for 2 credits when you want to print.
Start from this working example and replace any number with what you measured: Design a 50 mm plane-iron honing jig with 25 and 30 degree beds, 4 mm clamp bar, 608 bearing pocket, 2 mm PETG walls.
Freehand 25 degrees is a guess. In SpeakCAD you generate and preview for free, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More tools & jigs
Voron Trident belt-tension gauge cardA 1.2 mm card that reads Voron Trident A/B belt tension by how far a 6 mm span deflects to printed marks at 80, 90 and 100 Hz equivalents.Soldering fume-arm 50 mm hose clampA bench clamp that holds a 50 mm extractor hose 200 mm above a soldering iron rest.Pinecil V2 stand with brass-tip wellA stand that parks a Pinecil V2 at 45 degrees with a 10 mm brass-wool well and a 8 mm tip rack for three tips.Bosch L-BOXX 102 bit insertAn insert that holds 40 bits in an L-BOXX 102 (about 357 × 316 mm) on 7 mm rails so they replace the foam.Router circle-cutting jigA trammel jig lets a trim router cut clean circles and arcs by pivoting around a pin.Shimano SPD cleat alignment jig for cycling shoesA jig that holds a Shimano SM-SH51 or SH56 SPD cleat at a repeatable fore-aft position and angle while you tighten the two M5 bolts (14 mm apart), so a new p…