1
Organizers & storage
Gridfinity bin for Knipex Cobra 180 and 125
This is not a fixed STL. SpeakCAD generates the gridfinity bin for knipex cobra 180 and 125 to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create a 5×2 Gridfinity bin, 3 units tall, pockets for 180 mm and 125 mm water pump pliers, 1 mm offset, 14 mm deep, finger scoops.
What a gridfinity bin for knipex cobra 180 and 125 is
A 5 × 2 Gridfinity bin (209.5 × 83.5 mm, 3 units tall) with pockets for a Knipex Cobra 180 mm (87 01 180) and a Cobra 125 mm (87 01 125), jaws closed. Each outline is offset 1 mm from the pliers, 14 mm deep, with finger scoops at the handles. Print in PLA with the bin base down.
The Cobra XS (100 mm) and the pliers wrench have a different outline and rattle in these pockets. Open the ready-made bin in SpeakCAD for free, change any pocket in the viewer or the chat, then download the STL.
People also search
gridfinity knipex cobraknipex cobra holder stlgridfinity pliers binknipex cobra storage 3d print
Questions people ask about a gridfinity bin for knipex cobra 180 and 125
A 5 × 2 Gridfinity bin (209.5 × 83.5 mm, 3 units tall) with pockets for a Knipex Cobra 180 mm (87 01 180) and a Cobra 125 mm (87 01 125), jaws closed. Each outline is offset 1 mm from the pliers, 14 mm deep, with finger scoops at the handles. Print in PLA with the bin base down.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create a 5×2 Gridfinity bin, 3 units tall, pockets for 180 mm and 125 mm water pump pliers, 1 mm offset, 14 mm deep, finger scoops.
The Cobra XS (100 mm) and the pliers wrench have a different outline and rattle in these pockets. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More organizers & storage
ESP32 dev board storage rack with 10 slotsA desk rack that stores ESP32 DevKit, ESP32-C3, ESP8266 NodeMCU and Arduino Nano boards upright with their USB ports facing up so the right one is easy to grab.DJI Mini 4 Pro ND filter case with six slotsA pocket case for the snap-on ND filters used by the DJI Mini 4 Pro and Mini 3 Pro, which measure roughly 25 x 24 mm and 8 mm deep including the clip and are…Mac Studio M4 top SD-card caddyA caddy that sits on a Mac Studio M4 and holds six SD cards plus two CFexpress in labelled slots, 120 × 80 × 16 mm, rubber-foot recesses so it does not slide.Sony WH-1000XM6 travel-case insertAn insert that keeps XM6 cups from grinding in the official case, with two 90 mm cup wells and a 20 mm cable trough.Insta360 X4 travel case insertAn insert that turns a small box into a travel case for an Insta360 X4 (46 × 123.6 × 37.6 mm) and its kit.Gridfinity bin for 1/4 inch drive metric socketsA 3 × 2 Gridfinity bin (125.5 × 83.5 mm, 3 units tall) with twelve square posts for 1/4 inch drive sockets from 4 to 14 mm.