1
Everyday fixes
DJI Osmo Pocket 3 belt clip holster
This is not a fixed STL. SpeakCAD generates the dji osmo pocket 3 belt clip holster to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a belt holster for a DJI Osmo Pocket 3, 43×34.5 mm sleeve 95 mm long, closed cup over the gimbal, clip for 40 mm belts, 2 mm walls.
What a dji osmo pocket 3 belt clip holster is
A belt holster for the DJI Osmo Pocket 3 (139.7 × 42.2 × 33.5 mm) that carries it head-down with the gimbal protected. The sleeve is 43 × 34.5 mm inside and 95 mm long, the gimbal end is a closed 50 mm cup with 1 mm clearance around the camera, and a spring clip on the back fits belts up to 40 mm. Walls are 2 mm. Print upright in PETG.
It fits the bare Pocket 3; with the included magnetic cover on, use the cover instead. Open the ready-made model in SpeakCAD for free, change the belt width or any millimetre, then download the STL.
People also search
osmo pocket 3 belt clip stlpocket 3 holster 3d printdji pocket 3 holderosmo pocket 3 case 3d model
Questions people ask about a dji osmo pocket 3 belt clip holster
A belt holster for the DJI Osmo Pocket 3 (139.7 × 42.2 × 33.5 mm) that carries it head-down with the gimbal protected. The sleeve is 43 × 34.5 mm inside and 95 mm long, the gimbal end is a closed 50 mm cup with 1 mm clearance around the camera, and a spring clip on the back fits belts up to 40 mm. Walls are 2 mm. Print upright in PETG.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a belt holster for a DJI Osmo Pocket 3, 43×34.5 mm sleeve 95 mm long, closed cup over the gimbal, clip for 40 mm belts, 2 mm walls.
It fits the bare Pocket 3; with the included magnetic cover on, use the cover instead. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More everyday fixes
Nanit Pro floor-stand weight plateA 160 mm plate that adds printed mass and a 8 mm rubber-foot set under a Nanit floor stand so it does not walk.RTL-SDR V4 dipole-arm clipA clip that holds RTL-SDR V4 dipole arms at 90 degrees on a window, 8 mm snap.Canyon Grizl top-tube bag mountA mount that gives a Grizl two M5 bosses on 64 mm centres for a top-tube bag when the frame has only bottle mounts.Garmin Dash Cam Mini 2 headliner cable clipsA set of small clips that hold the power cable of a Garmin Dash Cam Mini 2 (about 31 × 53 × 29 mm) tidy along the headliner and A-pillar instead of dangling…Dashboard key and sunglasses holderKeys and sunglasses slide around a flat dash and end up under the seat.Kindle Paperwhite one-hand page-turn grip ringA stick-on ring grip for the back of a Kindle Paperwhite (176.7 x 127.6 mm on the 2024 model) that slips over two fingers so the tablet hangs from your hand…