1
Brackets & mounts
Blue Yeti shock mount with 5/8 thread
This is not a fixed STL. SpeakCAD generates the blue yeti shock mount with 5/8 thread to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a Blue Yeti shock mount, 40 mm cup with a 5/8-27 bolt, four elastic cords holding it in a 110 mm frame, 5/8-27 thread for a boom arm.
What a blue yeti shock mount with 5/8 thread is
A shock mount for a Blue Yeti that screws into the 5/8-27 thread in the bottom of the microphone once it is off its desk stand. A 40 mm cup holds the mic on a 5/8-27 bolt, four elastic cords suspend the cup inside a 110 mm frame, and the frame has its own 5/8-27 thread for a boom arm. Print the frame and cup in PETG and use 2 mm elastic cord.
The Yeti Nano is lighter, so the same cords sag less and isolate less; tell the chat to use thinner cord. Open the ready-made model in SpeakCAD for free, change any millimetre in the viewer or the chat, then download the STL.
People also search
blue yeti shock mount stlyeti shock mount 3d printblue yeti boom arm mountblue yeti shockmount
Questions people ask about a blue yeti shock mount with 5/8 thread
A shock mount for a Blue Yeti that screws into the 5/8-27 thread in the bottom of the microphone once it is off its desk stand. A 40 mm cup holds the mic on a 5/8-27 bolt, four elastic cords suspend the cup inside a 110 mm frame, and the frame has its own 5/8-27 thread for a boom arm. Print the frame and cup in PETG and use 2 mm elastic cord.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a Blue Yeti shock mount, 40 mm cup with a 5/8-27 bolt, four elastic cords holding it in a 110 mm frame, 5/8-27 thread for a boom arm.
The Yeti Nano is lighter, so the same cords sag less and isolate less; tell the chat to use thinner cord. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More brackets & mounts
Ukulele wall hanger for soprano and concertA compact wall hanger for soprano and concert ukuleles (about 35 mm nut width).Brompton handlebar mount for Garmin Edge computersBrompton M and S bars have a 22.2 mm grip section and very little real estate once the brake levers and shifter are on, so a normal out-front mount does not…Chuckit ball launcher wall mount with ball holderA garage or hallway mount that holds a Chuckit Classic 26M launcher upright by its handle and keeps two tennis balls ready beside it.Dyson V8 Absolute wand wall holsterA wall holster that parks a V8 Absolute wand and three click-in tools so you are not buying Dyson's official dock.LD2450 presence sensor tilt wall mountA wall mount for an HLK-LD2450 tracking radar (about 44 × 15 mm) that tilts it 15 degrees down, so the 120 degree field covers the room instead of the ceiling.Honda Civic 11th gen honeycomb vent phone mountA phone mount for the full-width honeycomb vent strip of a 2022 or later Civic, with two hooked prongs that go through the mesh and lock behind it instead of…