1
The prompt on this page opens in SpeakCAD already filled in — after sign-in too. The model renders in your browser. Preview is free.Desk & office
Apple Pencil Pro MagSafe pair tray
This is not a fixed STL. SpeakCAD generates the apple pencil pro magsafe pair tray to your millimetres, you adjust it in the chat, then you download and print it.2
Change any millimetre in the chat: wall thickness, hole size, the thing it clips onto. Iterations stay in the tab until it matches what you own.Adjust
3Print
Download a watertight STL or 3MF for 2 credits, drop it in your slicer, and print it. Small fit fixes re-download free.Get it nowThe example prompt comes with you, even through sign-in. Preview is free; a download costs 2 credits.
What a apple pencil pro magsafe pair tray is
A tray that parks an Apple Pencil Pro and a USB-C Pencil side by side with 9 mm saddles and a 12 mm cap well. 90 × 40 mm. Print in PLA.
Two pencils rolling off an iPad is a drop. In SpeakCAD you pick one or two, preview the tray in the browser at no cost, then download the STL.
Example prompt
Design an Apple Pencil pair tray 90×40×12 mm, two 9 mm saddles, 12 mm cap well, 1.2 mm walls.
People also search
apple pencil pro tray stlapple pencil holder 3d printpencil pro magsafe standapple pencil desk dock 3d model
Questions people ask about a apple pencil pro magsafe pair tray
A tray that parks an Apple Pencil Pro and a USB-C Pencil side by side with 9 mm saddles and a 12 mm cap well. 90 × 40 mm. Print in PLA.
Click Get it now on this page: the example prompt is filled in for you after you sign in. The model renders in your browser — nothing to install — and previewing is free. Adjust any millimetre in the chat, then export a watertight STL or 3MF for 2 credits when you want to print.
Start from this working example and replace any number with what you measured: Design an Apple Pencil pair tray 90×40×12 mm, two 9 mm saddles, 12 mm cap well, 1.2 mm walls.
Two pencils rolling off an iPad is a drop. In SpeakCAD you generate and preview for free, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More desk & office
ZSA Moonlander tenting legs setA set of four screw-in tenting legs for a ZSA Moonlander that replace the stock 8 mm feet with 15, 25 and 40 mm options.NuPhy Air75 V3 tenting feetA set of 8 degree tenting feet that replace Air75 V3 stock feet, 20 × 10 × 8 mm with the official pin.iPad Pro 13-inch M4 folio desk easelA low easel that holds a 13-inch iPad Pro M4 (about 281 × 215 × 5.1 mm) in its Smart Folio at 25 degrees for drawing, with a 218 mm ledge, a 10 mm Apple Penc…IKEA SKOGSTA table cable-clip pairA pair of clips that grab a SKOGSTA table apron (about 30 mm) and park a laptop charger so it does not hang in the walkway.Framework Desktop under-desk trayA ventilated tray that clamps a Framework Desktop (about 190 × 190 × 75 mm) under a 15–36 mm desk so the rear exhaust stays open.AirPods Pro 2 case charging stand for MagSafe puckA small stand that holds an Apple MagSafe puck at 70 degrees and cradles the AirPods Pro 2 case (60.6 x 45.2 x 21.7 mm) against it, aligning the case coil wi…