OrcaSlicer vs Bambu Studio in 2026: which to use with a Bambu Lab printer
OrcaSlicer and Bambu Studio compared for Bambu Lab owners in 2026: where each comes from, what differs in practice, and how a print reaches the printer.With a Bambu Lab printer, use Bambu Studio if you want the printer to work the way Bambu Lab built it: slice, press print, watch the camera, let the AMS colours map themselves. Use OrcaSlicer if you want its built-in calibration tests and finer control, own printers from other brands too, or prefer a community project, and accept one more step to start a print. Both are open source, free to download and from the same family, so presets and habits carry over.
The short answer
- A new Bambu Lab printer, the AMS, prints started from the slicer or the phone: Bambu Studio.
- Tuning a filament, hiding a seam, or one program for a Bambu Lab and a Klipper printer: OrcaSlicer.
- Both installed: nothing stops you. They are separate programs with the same Bambu Lab presets; use each for what it does well.
- No computer at hand: neither runs on a tablet or a phone. A browser slicer gives the same kind of sliced .gcode.3mf for the microSD card; the companion post on the .gcode.3mf covers that route.
Where they come from
The two are close relatives. Slic3r, by Alessandro Ranellucci and the RepRap community, came first. Prusa Research built PrusaSlicer on it. Bambu Lab based Bambu Studio on PrusaSlicer. OrcaSlicer then drew from Bambu Studio and PrusaSlicer, with ideas from Cura and SuperSlicer, and its repository says it has since grown well beyond that starting point. It is developed in the open by SoftFever and hundreds of contributors; Bambu Studio is developed by Bambu Lab. Both are published under the AGPL-3.0 licence.
That ancestry is why they look alike: the same plate, the same three kinds of preset (printer, filament, process), the same names for Bambu Lab's print profiles, such as 0.20mm Standard, and the same sliced file at the end.
Side by side
| Bambu Studio | OrcaSlicer | |
|---|---|---|
| Made by | Bambu Lab | An open-source project: SoftFever and hundreds of contributors |
| Based on | PrusaSlicer, itself based on Slic3r | Bambu Studio and PrusaSlicer, with ideas from Cura and SuperSlicer |
| Licence | AGPL-3.0 | AGPL-3.0 |
| Runs on | Windows 10 or later, macOS 10.15 or later, Linux from GitHub | Windows, macOS, Linux (Flathub or AppImage) |
| Printer profiles | Bambu Lab's printers first | Hundreds of printers: Bambu Lab, Prusa, Creality, Voron and many more |
| Known for | Projects with several plates, colour painting with automatic AMS mapping, remote control and monitoring | A built-in calibration suite, wall and seam control, scarf seams, sandwich mode, polyholes |
| Starting a print on a Bambu Lab printer | Directly, over Bambu's cloud or the local network | Through Bambu Connect, in Developer Mode on the local network, or from the microSD card |
| Network sending to other printers | Its page describes Bambu Lab printers | Printers running Klipper, PrusaLink or OctoPrint |
| Without the network plugin | Slice, then print from the SD card | Slice, export, then print from the card |
What differs in practice
Calibration. OrcaSlicer makes its test prints inside the program: flow rate, pressure advance, temperature towers, retraction, tolerance and maximum volumetric speed. For a filament that has no preset, this is its strongest argument.
Fine control. OrcaSlicer has settings for outer-wall spacing, scarf seams that hide the seam line, sandwich mode (inner wall, outer wall, inner wall) and polyholes for holes that measure true, and it lets speed, layer height and temperature be set per feature.
Colour and the AMS. Bambu Studio is built around it: add filaments to a project, paint the model with brushes, and each filament is mapped to an AMS slot before printing. OrcaSlicer handles multi-colour prints for Bambu Lab printers as well; what changes is how the job gets to the printer.
Projects. Bambu Studio organises work as a 3MF project with several plates, a resource manager and an assembly view, and it imports STEP files as well as STL.
Other printers. OrcaSlicer's profiles cover hundreds of machines, and it sends jobs to printers running Klipper, PrusaLink or OctoPrint. If a Voron or a Creality sits next to your Bambu Lab, one program does both.
Accounts. OrcaSlicer's site says it needs no account and sends no telemetry. Bambu Studio's cloud features use your Bambu Lab account; its network plugin is optional, and without it you slice and print from the SD card.
How a file reaches the printer
This is the real difference in 2026. It comes from the authorisation system Bambu Lab added to printer control, described on its wiki (read on 17 November 2026).
From Bambu Studio. Press print: the job goes over Bambu's cloud or the local network, and the same window controls and monitors the printer.
From OrcaSlicer. On firmware with the authorisation system, starting a print from software other than Bambu Studio takes one of three routes:
- Bambu Connect. Bambu Lab's small desktop app receives the sliced file and sends it to the printer, through your Bambu account or in LAN mode. It runs on Windows 10 or later and macOS 13 or later; Bambu Lab lists the Linux version as in development.
- Developer Mode. A setting on the printer, in LAN mode, under which third-party software talks to the printer as it did before. While it is on, the printer cannot connect to Bambu's cloud, and Bambu Lab said when it introduced the mode that it gives no customer support for it.
- The microSD card. Starting a print from the card is not affected. Export the sliced plate as a .gcode.3mf, copy it to the card and start it on the printer's screen.
Bambu Lab introduced the system on the X series first, with the P and A series to follow in later firmware, so what your printer asks for depends on its firmware. If one workflow matters to you, read Bambu Lab's wiki page and OrcaSlicer's release notes before you update the printer.
Which to use
- You just unboxed the printer. Bambu Studio. One program, one account, nothing to route.
- A filament without a preset, or a seam you want gone. OrcaSlicer, for the calibration and the seam settings; send the result whichever way your firmware allows.
- Bambu Lab and Klipper printers in the same room. OrcaSlicer, for one set of habits.
- You start prints from the phone with Bambu Handy. Bambu Studio, and leave Developer Mode off, since it cuts the printer off from Bambu's cloud.
- A Chromebook, an iPad or a phone, and no computer. Neither runs there. SpeakCAD's online slicer runs OrcaSlicer on a server with the bundled Bambu Lab presets and gives a sliced .gcode.3mf for the card. It takes one model per file with standard profiles: no colour painting, no modifiers, no custom start sequence. Free with a free account, no card, no credits: up to 10 files a day (60 on a paid plan).
Look elsewhere than Bambu Studio if you run printers from several brands, or want OrcaSlicer's calibration suite. Look elsewhere than OrcaSlicer if an extra app or a card between the slicer and the printer would annoy you every day.
Download them from the right place
Bambu Studio comes from Bambu Lab's download page (Windows and macOS) or its GitHub releases (Linux). OrcaSlicer comes from orcaslicer.com or the project's GitHub releases, and nowhere else: its repository warns that look-alike sites with similar addresses pose as the official one and may lead to dangerous downloads.
Moving between them
Because OrcaSlicer carries Bambu Lab's presets, a part sliced in either with the same printer, filament and process preset is the same kind of job. Presets you tuned yourself live in each program separately, so copy the numbers across and check with a small print before a long one. The printer pages list each model's bed size and layer heights from its profile: the A1, the P1S and the X1 Carbon.
Choosing among more than these two: the best slicers by printer and by device, and Cura vs PrusaSlicer vs OrcaSlicer for printers of other brands.
Sources
Read on 17 November 2026:
- Bambu Lab: the Bambu Studio page and the bambulab/BambuStudio repository
- Bambu Lab's wiki: third-party integration with Bambu Lab products
- Bambu Lab's blog, 20 January 2025: updates and third-party integration with Bambu Connect
- OrcaSlicer: the OrcaSlicer/OrcaSlicer repository and orcaslicer.com
The online slicer is free with a free account (no card, no credits): up to 10 files a day, and re-slicing the same file with other settings within 24 hours does not count. Accounts on a paid plan slice up to 60 files a day.
Questions
It depends on what you want. Bambu Studio is Bambu Lab's own slicer: it maps colours to the AMS and sends, controls and monitors prints directly over Bambu's cloud or the local network. OrcaSlicer has the same Bambu Lab presets, adds a built-in calibration suite and finer wall and seam control, and covers hundreds of other printers, but on firmware with Bambu Lab's authorisation system, starting a print from it takes Bambu Connect, Developer Mode or the microSD card.
Yes, by one of three routes described on Bambu Lab's wiki. Bambu Connect, Bambu Lab's desktop app for Windows and macOS, receives the sliced file and sends it to the printer. Developer Mode, in LAN mode, lets third-party software talk to the printer as before, without Bambu's cloud. And a sliced .gcode.3mf copied to the microSD card starts from the printer's screen. Which one applies depends on the printer's firmware.
Yes, in part. Bambu Studio is based on PrusaSlicer, which is based on Slic3r. OrcaSlicer's repository says it drew from Bambu Studio and PrusaSlicer, with ideas from Cura and SuperSlicer, and has since grown well beyond that. Both are open source under the AGPL-3.0 licence.
Yes. They are separate programs that install side by side, and both carry Bambu Lab's printer, filament and process presets. A sensible split is Bambu Studio for everyday prints sent over the network, and OrcaSlicer for calibrating a new filament or for printers from other brands.
Yes, in a browser. SpeakCAD's online slicer runs OrcaSlicer on a server with the bundled Bambu Lab presets and gives a sliced .gcode.3mf to copy to the printer's microSD card. It takes one model per file with standard profiles, without colour painting or modifiers. The online slicer is free with a free account (no card, no credits): up to 10 files a day, and re-slicing the same file with other settings within 24 hours does not count. Accounts on a paid plan slice up to 60 files a day.