Slicing: from STL to G-code for your printer

How to cut 3D print time in 2026 without weakening the part

Six ways to shorten a 3D print in 2026, in order of effect: layer height, infill and walls, nozzle, orientation, the design, speed. With the arithmetic.
17 November 2026 · 7 min readprint timeslicingsettings

Print time is roughly the number of layers multiplied by the length of plastic laid on each one. So the real savings come from fewer layers, less plastic per layer and a wider line, and speed settings come last because the printer's own limits cap them. Here are the six levers in order of effect, with the arithmetic for each and what it does to the strength of the part.

The short answer

  • Thicker layers first. 0.28 mm instead of 0.20 mm is 29% fewer layers, for little loss of strength.
  • Then infill, not walls. Drop infill to 15% on parts that carry no load; keep three walls or more.
  • A larger nozzle for big parts. A 0.6 mm nozzle builds the same wall in two thirds of the passes.
  • Lay it down, lose the supports. Fewer layers, and often a stronger part.
  • Change the design. Lower, thinner where nothing pulls, chamfers instead of ledges.
  • Speed last. A faster profile saves less than its number suggests.

Measure every change instead of guessing: the 3D print time calculator slices your file for your printer without an account.

The six levers at a glance

LeverExample changeThe arithmeticEffect on strength
Layer height0.20 mm to 0.28 mm0.20 ÷ 0.28 = 0.71, so 29% fewer layersSmall
Infill30% to 15%Half the infill; walls, top and bottom unchangedSmall on parts without load
Walls5 to 3Two loops fewer around every outline, on every layerReal: cut with care
Nozzle0.4 mm to 0.6 mmA 2.4 mm wall is 6 lines or 4; layers can go to about 0.4 mmNone at the same wall thickness
OrientationStanding to lyingA 120 x 20 x 20 mm bar: 600 layers or 100, at 0.20 mmOften a gain
SpeedNormal to Fast1.3 times on walls, infill, top and supports onlyFine for drafts

1. Layer height: the biggest lever

Every layer is one full pass over the part, so the layer count sets the baseline. A part 60 mm tall is 300 layers at 0.20 mm, 250 at 0.24 mm and about 215 at 0.28 mm. The time follows the layer count closely, though not exactly: thicker layers push more plastic per second, and the filament's flow limit can slow the widest lines.

What it costs is looks, not strength: within the usual 0.08 to 0.28 mm range on a 0.4 mm nozzle, layer height changes strength far less than walls and orientation. Keep 0.12 to 0.16 mm for threads, small snap features and text; use 0.24 to 0.28 mm for boxes, brackets and anything nobody inspects closely. Slicer settings for functional parts has the full ranking.

2. Infill and walls: cut the first, keep the second

Infill is the sparse pattern inside the part. Past about 25 to 30% it adds strength slowly, and 10 to 15% is enough for enclosures, covers and most parts that carry no load, so this is the safe place to save. How much it saves depends on the shape: a chunky part holds a lot of infill and gains a lot, while a thin bracket or a box wall is nearly all walls and gains almost nothing.

Walls are the opposite. Each one is a loop around every outline on every layer, so going from five walls to three removes two loops in five. But bending and twisting loads are carried by the outside of a part, and screws grip walls. Two walls for light enclosures and trays, three for general parts and anything with screws, four to five for brackets and hooks: go below that only when the part carries nothing. How to make 3D printed parts stronger starts from the other end.

3. Nozzle size: fewer, wider lines

A 0.4 mm nozzle lays lines about 0.42 to 0.45 mm wide. A 0.6 mm nozzle lays lines half as wide again, so a 2.4 mm wall takes four passes instead of six, and it prints well with layers around 0.3 to 0.4 mm. Together, that is the largest saving available on a big functional part, without thinning anything.

The costs: small holes, sharp corners and fine text lose definition, and the slicer must be told, because every line is planned for the nozzle you select. Choose the 0.6 mm profile only when that nozzle is installed. 0.2 vs 0.4 vs 0.6 mm nozzles compares the three.

4. Orientation and supports

Layers scale with height, so the same part takes very different times depending on which face is on the bed. A bar 120 x 20 x 20 mm is 600 layers standing on its end and 100 lying down, at 0.20 mm. Each of those 100 layers is larger, so the print is not six times shorter; what you save is the travel, the starts and stops, and the small layers of a tall narrow print, which the printer slows down so they can cool.

Lying down also tends to remove supports, which cost extra paths on many layers, slower interface layers under the part, and cleanup. Why does my print need supports? explains the 45° rule.

This lever usually helps strength as well, since a printed part is weakest between layers: a hook printed on its side carries its load along the layers instead of across them. When time and strength disagree, strength wins. Automatic orientation picks the flattest base and the fewest overhangs, which is right for time and not always for load.

5. Change the design itself

A slicer prints the model as it is, and the largest savings are sometimes in the model.

  • Lower it. A tray 25 mm tall instead of 40 mm is 75 fewer layers at 0.20 mm.
  • Thin it where nothing pulls. 1.2 to 1.6 mm walls are plenty for organisers and trays, 1.6 to 2.4 mm for enclosures; a floor needs about 1 mm. Thickness beyond that is time.
  • Replace ledges with chamfers. A 45° chamfer under a ledge prints without supports.
  • Make walls a whole number of lines. 1.25 or 1.7 mm instead of 1.0 or 1.5 mm with a 0.4 mm nozzle, so the slicer does not have to fill gaps.
  • Test the fit before the long print. A Fit Check coupon, a five-minute piece of just the fit, is far shorter than printing the whole part twice.

Not everything that removes plastic removes time: a hole or a window adds walls around it. In SpeakCAD, the hand tools cut, shell and chamfer a part you shaped there, with every size typed in millimetres. For an STL you downloaded, the AI editor rebuilds it as an editable model and makes the change you describe, which spends credits.

6. Speed profiles: the smallest lever

A printer's profile already runs each kind of line near what the machine and the plastic allow. A Fast setting (1.3 times in SpeakCAD's online slicer) raises the wall, infill, top and support speeds, but acceleration, travel moves and the minimum time per layer stay the same, and the filament's flow limit caps the result. The print gets shorter by less than the factor.

Speed does not weaken a part as long as the plastic still melts fully, which is what the flow limit in the filament preset protects. Pushing past it by hand is how fast prints turn weak and rough. Use Fast for drafts and test fits, Normal for a part that must be accurate. The material matters too: a PETG preset runs slower and with less fan than a PLA one, so the same part takes longer in PETG.

What not to cut

Walls on anything with a screw or a load (three is the floor), and an orientation chosen for strength: a bracket that breaks is the slowest print of all.

Check the saving before you print

Change one thing, slice again and compare the hours and the grams. The print time calculator and the print cost calculator do it without an account, up to 10 estimates a day, and return the numbers only. The online slicer gives the same numbers with the file to print. Free with a free account, no card, no credits: up to 10 files a day (60 on a paid plan). Expect the real print to run a little over the estimate: heating, bed levelling and the purge line come on top.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

Prompts to start from

Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.

An open tray 120 x 80 x 25 mm with 1.6 mm walls and a 1.2 mm floor, with 45 degree chamfers instead of ledges so it prints without supports

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

An L bracket 60 x 40 mm, 25 mm wide and 4 mm thick, shaped to print lying on its side without supports, with two M4 countersunk holes on each leg and a 3 mm fillet inside the bend

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A clip for an 8 mm cable, 12 mm wide with 2 mm walls and a flat base so it prints flat without supports, fixed with one M3 screw through a 3.4 mm hole

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

Questions

Use a thicker layer height: 0.28 mm instead of 0.20 mm is 29% fewer layers, with little effect on strength. Then lay the part down to cut its height and its supports, lower the infill on parts that carry no load, and use a 0.6 mm nozzle for large parts. Speed settings save the least, because the printer's and the filament's limits cap them.

Very little within the usual 0.08 to 0.28 mm range on a 0.4 mm nozzle. Layer height changes how a part looks and how long it takes far more than how strong it is; the number of walls and the direction of the layers decide strength. Keep thin layers for threads, small snap features and text.

It depends on the shape. A chunky part holds a lot of infill, so going from 30% to 15% saves a lot. A thin bracket or an enclosure wall is nearly all walls and top and bottom layers, so infill changes little. 10 to 15% is enough for enclosures and most parts without load; keep three or more walls for strength.

For large parts, yes. Its lines are half as wide again, so a 2.4 mm wall takes four passes instead of six, and it prints well with layers around 0.3 to 0.4 mm, which means fewer layers. Small holes, sharp corners and fine text lose definition, and the slicer must be set to the nozzle that is installed.

Not while the plastic still melts fully. A filament preset caps the flow so that it does, and a Fast setting stays under that cap, which is also why it saves less time than its factor suggests. Forcing speeds past the flow limit gives weak, rough parts. Use Fast for drafts and Normal for parts that must be accurate.

Slice your STL in the browser

Drop an STL or 3MF, pick your printer among 380+ models from 60+ brands with their OrcaSlicer profiles, and download G-code ready to print, with the print time and filament weight. The online slicer is free with a free account (no card, no credits): up to 10 files a day, and re-slicing the same file with other settings within 24 hours does not count. Accounts on a paid plan slice up to 60 files a day.