Easy CAD for 3D printing: the hand tools, and when to ask the AI

Ø, R, 4× and ±: how to read a dimension drawing before you design a part around it

The board, motor or fan your part must fit often has a dimension drawing. What Ø, R, 4×, ±, TYP and the dashed lines mean, and how to turn them into a part.
17 November 2026 · 6 min readdrawingsmeasuringbeginners

The thing your part has to fit often comes with its measurements already taken. A development board, a motor, a fan, a hinge or a connector usually has a dimension drawing on its product page or in its datasheet. For one job, hole positions, it is better than your callipers, and it is written in a shorthand that nobody explains. Here is the shorthand, and how to turn a drawing into numbers you can type.

Why bother with the drawing

  • Hole centres. A drawing gives the distance between hole centres directly. Callipers cannot touch a centre.
  • Things you cannot reach. The height of the tallest component, the position of a connector under a shield.
  • The size that was intended. A drawing says 58 mm. Callipers say a little under on one unit and a little over on the next.

Still measure the one dimension that decides the fit yourself. A drawing describes the part as designed, and the one on your desk may be another revision.

The symbols

On the drawingMeansExample
ØDiameter of a circleØ3.2 is a hole 3.2 mm across
RRadius, half a diameterR4 is a corner rounded with a 4 mm radius
4×, 4X or (4 PLACES)The dimension applies to four identical features4× Ø3.2 is four holes of 3.2 mm
±Tolerance: how far the real size may be from the stated one58 ± 0.2 is anything from 57.8 to 58.2
MAX, MINA limit, not a target12 MAX is never taller than 12 mm
( ) or REFReference: worked out from other dimensions, for information(68)
TYPTypical: the same wherever this feature repeatsR2 TYP is every such corner
THRUThe hole goes all the way throughØ3.2 THRU
M3, M4A metric thread, named by its diameter in millimetresM3 is a 3 mm thread
PCD or B.C.Pitch circle or bolt circle: holes spaced round a circle of this diameter4× Ø4.5 on PCD 50
□A square of this side□40

The lines

  • Thick solid lines are edges you can see.
  • Dashed lines are edges hidden behind the surface, such as a pocket on the far side.
  • Long-dash, short-dash lines are centre lines. Where two of them cross is the centre of a hole or of a round part, and hole positions are dimensioned to that point, not to the edge of the hole.
  • Thin lines ending in arrows are the dimensions themselves. The two thin lines they run between show exactly what is being measured: follow them back to the part.

The views

A drawing shows a part flat, from one direction at a time: usually from the top, the front and one side, arranged round each other. Length and width come from the top view, heights from the front or the side view. If a dimension seems to be missing, it is in another view.

Units, and the note in the corner

Look in the title block or the notes for "DIMENSIONS IN MM" or "UNITS: INCH". Some drawings are in inches, sometimes with millimetres in square brackets beside each number: 2.283 [58.0]. If no unit is stated and a small board is "2.3" wide, it is inches. Multiply by 25.4 before anything else; millimetres or inches? covers the traps.

The same corner often carries a general tolerance, such as "unless stated, ± 0.2", which applies to every dimension that has none of its own.

From a drawing to a part: a worked example

Suppose the drawing of a small board (an invented one) shows this:

  • an outline 70 × 50, corners R3
  • 4× Ø3.2 THRU, on centres 62 × 42, the pattern centred on the outline
  • component height 12 MAX above the board, board thickness 1.6

A tray that holds it needs four standoffs under those holes. Work it out in this order.

  1. Hole positions on the board. The pattern is 62 long on a 70 outline, so each hole centre is (70 − 62) ÷ 2 = 4 mm from the short edges, and (50 − 42) ÷ 2 = 4 mm from the long ones.
  2. The pocket. The board slides in, so 0.5 mm per side: the inside is 71 × 51 mm. With 2 mm walls the outside is 75 × 55 mm.
  3. Hole positions in your part. The board sits 0.5 mm from the inner walls, so each standoff centre is 4 + 0.5 = 4.5 mm from two inner walls, or 6.5 mm from the outside of the tray.
  4. The screws. Ø3.2 on the board is for an M3 screw. A standoff that an M3 screw cuts its own thread into gets a 2.5 mm hole.
  5. Heights. Use the MAX: 12 mm of components, plus the 1.6 mm board, plus the standoff, plus a millimetre to spare.

Step 3 is the one that catches people. The drawing's dimensions run from the board's edge; your part's run from its own. Inside or outside? has the sums behind step 2.

Typing it in

By hand in SpeakCAD, a position is typed the way a drawing gives it: the centre's distance from two edges of the face you tapped. Tap the inner floor, Add a cylinder with its centre 4.5 mm from two inner walls, then Duplicate it in a Grid with spacings of 62 and 42, and the pattern is the drawing's. A hole at an exact distance from the edge and hole patterns show the taps.

Or describe it to the AI, reading the drawing out in one order: the outline, the hole pattern with its count, diameter and spacing, the heights, then the fit.

A tray for a board 70 × 50 × 1.6 mm with four mounting holes on 62 × 42 mm centres, centred on the board. Four standoffs 5 mm tall for M3 self-tapping screws, 0.5 mm clearance round the board, 2 mm walls, 13 mm of room above the board.

What a drawing does not tell you

  • How your printer prints. The drawing's ± is the maker's tolerance. Your clearance comes on top of it.
  • Which revision you own. Check one dimension with callipers (how to use them).
  • Cables and plugs. A connector is drawn; the plug that goes into it, and the bend of its cable, are not.

The words for the features you are about to ask for (standoff, boss, lip, flange) are in the names of a part's features, and the general CAD vocabulary is in the glossary. CAD for beginners explains why a position measured from two edges is one of the first ideas to learn.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

Prompts to start from

Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.

A tray for a board 70 x 50 x 1.6 mm with four mounting holes on 62 x 42 mm centres, centred on the board. Four standoffs 5 mm tall for M3 self-tapping screws, 0.5 mm clearance round the board, 2 mm walls, 13 mm of room above the board.

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A mounting plate 60 x 60 x 3 mm with four 4.5 mm holes on a 50 mm bolt circle and a 22 mm hole in the centre

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

An adapter plate 80 x 80 x 4 mm with four M3 clearance holes on 31 x 31 mm centres and four M4 clearance holes on 60 x 60 mm centres, both patterns centred

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

Questions

Diameter. Ø3.2 is a circle, usually a hole, 3.2 mm across. R is a radius, half a diameter: R4 is a corner rounded with a 4 mm radius.

That the dimension applies to four identical features. 4× Ø3.2 THRU means four holes of 3.2 mm that go all the way through. Some drawings write 4X or (4 PLACES).

Take the spacing between hole centres from the drawing, work out each centre's distance from the edges of the board, then add your clearance and your wall to get its distance from the edges of your own part. For a 62 mm pattern centred on a 70 mm board, each centre is 4 mm from the board's edge.

Shape it by hand, free

Open a box or a plate, tap where the hole goes, type the size and download the STL with a free account; the AI is there when you would rather describe the part, at 4 credits a part on a plan, its first 3 small changes free.