Millimetres or inches? Why a 3D model arrives 25.4 times too small, and which unit to design in
An STL carries no unit, so a model drawn in inches opens 25.4 times too small. How to spot the factor, the one scale that fixes it, and why to design in mm.You open a downloaded model and it is a speck in the middle of the bed. Or it is so large that one corner fills the screen. Nothing is broken. The model was drawn in one unit and read in another, and the file had no way to tell anyone which.
An STL has no unit
An STL file is a list of triangles and nothing else. A corner at "25.4" is 25.4 of something: the file does not say millimetres, inches or metres. For 3D printing the convention is millimetres, so a slicer reads every number as millimetres. A part drawn 2 inches wide and saved without converting says "2", and arrives 2 mm wide.
A 3MF file stores its unit, which is one reason to prefer it when you have the choice. STL vs 3MF compares the two.
The factor tells you what happened
Compare one size on screen with the size the part should be. The ratio is nearly always one of four.
| What you see | Factor | What happened | Scale to apply |
|---|---|---|---|
| A speck, 25.4 times too small | 25.4 | Drawn in inches, read as millimetres | 2540 % |
| Small, 10 times too small | 10 | Drawn in centimetres | 1000 % |
| Invisible, 1,000 times too small | 1,000 | Drawn in metres | 100000 % |
| Huge, 25.4 times too big | 1 ÷ 25.4 | Drawn in millimetres, then converted as if it were inches | 3.937 % |
A worked example: a phone stand that the slicer reports as 3.1 × 2.8 × 4.3 mm is not a miniature. Multiply by 25.4 and it is 79 × 71 × 109 mm, which is a phone stand.
Some slicers offer to do this for you: when a model looks very small, they ask whether it is in inches. Say yes if it really was drawn in inches, and no otherwise. A part that is small on purpose, such as a 6 mm spacer, triggers the same question, and accepting turns it into a 152 mm disc.
The one time scaling is the right fix
Scaling a model to make it fit is usually a mistake, because the screw holes and the walls scale with it. A unit conversion is the exception: scaling by exactly 2540 % puts every dimension back where the designer drew it, holes included. Type the factor into the slicer's scale box with the three axes locked together, then check one dimension you know.
If the size is off by any other amount, 4 % or 12 %, it is not a unit problem. Someone resized the model, or it was made for a different thing. Why a downloaded STL does not fit sorts out which.
Which unit to design in
Millimetres, even if you think in inches. Everything a printer does is counted in them.
- The nozzle is 0.4 mm and lays a line a little wider than that. Walls print well as a whole number of lines, which is why 1.2 mm, three lines, is the usual minimum.
- Layers are usually 0.2 mm, so a 1 mm floor is five of them.
- Fits are tenths of a millimetre. 0.2 mm per side for a snug lid, 0.5 mm for a part that slides. In inches those are 0.008 and 0.020, and no tape measure shows either.
- Metric screws have simple names. An M3 screw is 3 mm across its thread and passes through a 3.4 mm hole; an M4 through 4.5 mm.
- The file convention is millimetres, as above. A model drawn in millimetres opens at the right size in any slicer.
SpeakCAD works in millimetres throughout: every size and position you type is a millimetre, the STL it writes is in millimetres, and the 3MF says so inside the file. If a slicer asks whether a file from SpeakCAD is in inches because the part is small, the answer is no.
If your tape measure reads inches
Convert before you type: multiply by 25.4. The fractions that come up most often:
| Inches | Millimetres |
|---|---|
| 1/16 | 1.5875 |
| 1/8 | 3.175 |
| 1/4 | 6.35 |
| 3/8 | 9.525 |
| 1/2 | 12.7 |
| 3/4 | 19.05 |
| 1 | 25.4 |
| 2 | 50.8 |
Round to the nearest tenth once you have converted. A digital calliper switches between the two units with a button; leave it on mm and you never convert at all (how to use callipers).
Names that are not sizes
Inch sizes hide a second trap: many of them are names, not measurements.
- A "2 by 4" plank is 1.5 × 3.5 inches, or 38 × 89 mm.
- A US "half-inch" PVC pipe is 21.3 mm across the outside, not 12.7.
- A "quarter-inch" tripod screw is the real thing: 6.35 mm across its thread.
Metric has the same habit in a milder form: an M3 screw needs a 3.4 mm hole, and a 0.4 mm nozzle lays a line of about 0.42 to 0.45 mm. So measure the thing in front of you and type what the callipers say, not what the label says.
Check the size before you print
One known dimension is enough. In a slicer, select the model and read its size. In SpeakCAD, the editor shows the model's outside dimensions under the render, and the Measure tool reads any distance with two taps. Compare with the one number you are sure of: the width of the thing the part must fit. A factor of 25.4 means inches crept in somewhere; anything else means the wrong file, or a resized one.
The slicer is the right place to fix a unit and the wrong place to fix a fit. CAD or slicer: which one changes what draws the line between the two. And if you are starting to design your own parts, CAD for beginners begins with the habit that makes all of this easy: every size is a number in millimetres that you type.
Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.
Prompts to start from
Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.A cap for a pipe 21.3 mm outside diameter, 20 mm deep, 0.2 mm clearance per side, 2 mm wall, closed end
A plate 101.6 x 50.8 x 3.2 mm with a 6.6 mm hole 12.7 mm from each short end, centred across the width
A spacer 19 mm across and 6.4 mm tall with a 6.6 mm hole through the middle, for a quarter-inch bolt
Questions
Most often because it was drawn in inches. An STL file carries no unit and slicers read its numbers as millimetres, so a part 2 inches wide arrives 2 mm wide. Scale it by 2540 % with the three axes locked together and check one dimension you know.
Neither: an STL stores numbers with no unit. The convention for 3D printing is millimetres, and slicers assume it. A 3MF file stores its unit, which removes the doubt.
In millimetres. Nozzle widths, layer heights, wall thicknesses, metric screw holes and clearances are all given in millimetres, and model files are read as millimetres. If your tape reads inches, multiply by 25.4 before you type.
Scale it by 2540 % (a factor of 25.4) in the slicer, on all three axes together. This is a unit conversion, so every hole and wall returns to its designed size. For a model drawn in centimetres the factor is 10, or 1000 %.