Easy CAD for 3D printing: the hand tools, and when to ask the AI

Sketch it on paper first: the five-minute drawing that saves a reprint

Before any CAD, draw the thing your part fits, then the part round it: two views, one corner as zero, every number written down. Six steps and an example.
17 November 2026 · 5 min readplanningbeginnerscad

A first part usually goes wrong before any software is open. A size is decided halfway through, a hole is placed by eye, and nobody asks which face sits on the bed until the slicer does. Five minutes with a pencil settles all three. You do not need to draw well: two rough rectangles with numbers on them are a complete plan.

What the sketch is for

It is not a picture of the part. A sketch is a list of decisions with a drawing attached, so that when you sit down at the screen you are typing numbers, not inventing them. It answers four questions.

  • What does the part touch, and how big is that?
  • Where is everything, measured from one corner?
  • Which dimensions decide the fit, and what gap does each get?
  • Which face goes on the bed?

Six steps

1. Draw the thing it fits, not the part

Start with the object that already exists: the shelf edge, the tube, the board, the two screws in the wall. Draw it from above and from the side, as two flat outlines, and write its measured sizes on it. This is the one part of the sketch that is not up to you, so it goes down first.

2. Draw the part round it

Now draw your part round the object, in another colour or with a heavier line. The top view is for length and width, the side view for heights. Leave a visible gap where the two meet: that gap is the clearance, and drawing it stops you forgetting it.

3. Pick a corner as zero

Choose one corner of your part, mark it, and write every position as a distance from that corner: "hole, 6 from the left, 6 from the front". Do not chain measurements from hole to hole, because each link adds its own error. One corner also matches how you will place things later: in SpeakCAD, the centre of a hole is typed as its distance from two edges of the face.

4. Write the numbers, then circle the ones that decide the fit

Put a size on every line. Then circle the two or three that have to match the object, and next to each write the clearance: 0.2 mm per side for a cap that stays on, 0.5 mm for something that slides, 1 mm for something that drops in. Everything not circled is yours to choose, and round numbers are fine: a 2 mm wall, a 3 mm plate, a 40 mm arm.

5. Mark the bed face and look for overhangs

Draw an arrow at the face that will lie on the bed. Then look at the side view and ask what hangs out over nothing. Anything that leans more than 45° from vertical needs supports or a rethink: a ledge can become a 45° chamfer, or the part can lie on another face. For a hook or a clip, pick the face that puts the layers along the bend, not across it.

6. Hold it against the real thing

Draw the top view again at full size (squared paper helps), cut it out and lay it on the object. Do the holes land on the screws? Does the arm clear the hinge? Corrugated cardboard does the same for a part with thickness. It takes two minutes and no printer.

A sketch in words

For a clip that holds a cable under the edge of a shelf, the finished sketch says:

  • Shelf: 18.2 thick, measured in three places
  • Slot in the clip: 18.6 (0.2 per side), 25 deep
  • Clip: 20 wide, 3 mm walls
  • Cable hook underneath: for an 8 mm cable, with a 6 mm opening so the cable pushes in and stays
  • Bed face: the side of the clip, so the layers run round the C
  • Circled: the 18.6 and the 6 mm opening

That is the part. What remains is typing.

From the sketch to the screen

By hand. Build in the order the sketch suggests, largest shape first. Start from the box, the plate or the cylinder nearest to the outline and type its outside sizes. Then cut what comes out: the slot, the pocket, the holes, each placed from your zero corner. Round and chamfer last, since those depend on the edges being final. The hand tools are Hole, Cut, Add, Extrude, Text, Round, Fillet, Shell and Measure; using them is free, and so is the STL or 3MF of what you shaped by hand.

By description. Read the sketch out in one message: what the part is for, the object's sizes, the circled fits with their clearance, then the choices that were yours. The six lines above are already a good description. If the shape is hard to put into words, a photo helps, but type the numbers anyway: a photo has no scale. How to describe a part has a template, and the names of a part's features has the words.

Either way, read the part back against the sketch before printing. Tick each number off on paper as you find it on screen with the Measure tool.

When to skip the sketch

A spacer, a plain plate, a box with one size that matters: go straight to the screen. Sketch when the part touches the object in more than one place, when it has holes that must meet existing screws, or when you cannot say in one sentence which face goes on the bed.

If the object came with a dimension drawing, half of the sketch is done for you: how to read one. For a case or a tray, inside or outside? has the sums that go beside the circled numbers. And if you have not chosen the part yet, what to design first has seven that need almost no sketch at all.

CAD for beginners names the six ideas every CAD program shares. A paper sketch practises several of them before you touch a screen: sizes as numbers, positions measured from edges, a gap where two things meet, and the printer's own rules.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

Prompts to start from

Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.

A clip for the edge of a shelf 18.2 mm thick: slot 18.6 mm wide and 25 mm deep, clip 20 mm wide with 3 mm walls, and a hook underneath for an 8 mm cable with a 6 mm opening

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A plate 90 x 40 x 3 mm with two M4 clearance holes, each 8 mm from a short edge and centred across the width

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

An L bracket 50 x 50 mm, 25 mm wide, 4 mm thick, 3 mm fillet inside the bend, two M4 clearance holes on each leg

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

Questions

Not for a spacer or a plain plate. Sketch when the part touches the object in more than one place, when holes must meet existing screws, or when you cannot say which face goes on the bed. Five minutes on paper is quicker than a reprint.

The object it fits with its measured sizes, the part drawn round it from above and from the side, every position measured from one corner, the fit dimensions circled with their clearance, and an arrow on the face that goes on the bed.

Draw the top view at full size on paper, cut it out and lay it on the real object to check that the holes and the edges land where they should. Corrugated cardboard does the same for a part with thickness.

Shape it by hand, free

Open a box or a plate, tap where the hole goes, type the size and download the STL with a free account; the AI is there when you would rather describe the part, at 4 credits a part on a plan, its first 3 small changes free.