1
SpeakCAD for the Bambu Lab H2D
Custom parts for the Bambu Lab H2D: describe them, download a .gcode.3mf sliced for it
Bambu's dual-nozzle machine with the large 350 x 320 mm bed, for parts that did not fit the 256 mm printers. SpeakCAD ships the Bambu Lab H2D's own OrcaSlicer profile: describe a part in plain English, watch it render on a virtual 350 x 320 mm bed, edit it by chat, and download a sliced .gcode.3mf, the file Bambu printers read from the microSD card and that Bambu Studio sends over the network. Or take the STL or 3MF to your usual slicer. Runs in Safari and Chrome, on a phone or a computer, nothing to install.
How it works
From a sentence to the H2D's microSD card
The slicer runs on our side with the same profiles OrcaSlicer ships for the Bambu Lab H2D. You choose the print profile and the filament; the printer settings are already right.2
Check it on the H2D's bed
The part renders on a virtual bed the size of the H2D's. The first render usually appears within a minute or two: a new part goes to the strongest models, which reason through the geometry, and small edits land in seconds. Turn it, tap a face to read a size, open the dimensions panel, and see whether it has overhangs that need supports. Anything wrong is one sentence to fix.3
Pick the Bambu Lab H2D and its profile
In the download dialog choose the Bambu Lab H2D (0.2 nozzle, 0.4 nozzle, 0.6 nozzle, 0.8 nozzle), one of its print profiles (0.08 mm, 0.1 mm, 0.12 mm, 0.16 mm…), a filament, then infill, walls, supports and adhesion. The printer and its last settings are saved to your account.4
Download and print
You get a sliced .gcode.3mf, the file Bambu printers read from the microSD card and that Bambu Studio sends over the network, with the estimated print time and filament weight. Re-slicing a design you already downloaded does not spend the 10 credits again; without Pro or Unlimited each slice still spends 5 credits.The Bambu Lab H2D profile SpeakCAD slices with
| Setting | Value |
|---|---|
| Printer | Bambu Lab H2D (Bambu Lab) |
| Printable area in the profile | 350 x 320 x 325 mm |
| Nozzle variants | 0.2 nozzle, 0.4 nozzle, 0.6 nozzle, 0.8 nozzle |
| Layer heights in the print profiles | 0.08 mm, 0.1 mm, 0.12 mm, 0.16 mm, 0.18 mm, 0.2 mm, 0.24 mm, 0.3 mm, 0.32 mm, 0.4 mm |
| Filament profiles | PLA, PETG, ABS, ASA, TPU, PLA-CF, PETG-CF, PC, PA, PA-CF, plus the OrcaSlicer filament library |
| Download | Sliced .gcode.3mf (Bambu), or STL and 3MF for your own slicer |
| Slicer | OrcaSlicer, run on our servers with the printer's official profile |
Prompts sized for the H2D
Copy one, change the numbers to yours. Each opens in the editor with the text already typed.“A build plate wall rack for Bambu Lab H2D plates: holds three 350 x 320 mm plates vertically in 8 mm slots 20 mm apart, two keyhole mounts, 3 mm walls, 300 mm wide.”
Open this prompt in the editor“A single-piece drawer organizer 300 x 200 x 50 mm with six compartments in two rows, 1.6 mm dividers, finger notches, 2 mm floor.”
Open this prompt in the editor“A monitor riser 320 x 220 x 90 mm, hollow with 20 mm ribs, a 60 x 30 mm cable pass-through at the back, printed in one piece.”
Open this prompt in the editorWhy H2D owners do not need a slicer on the phone
Slicing is the step that keeps 3D printing on the desktop: a design made anywhere still has to pass through Bambu Studio, PrusaSlicer or Cura on a computer. SpeakCAD runs OrcaSlicer on its own servers with the profile OrcaSlicer ships for the Bambu Lab H2D, so the phone that typed the description also downloads a .gcode.3mf. The desktop slicer stays the better choice for arranging many parts on one bed or for exotic settings; for one part at a time, the download dialog covers the profile, the filament, infill, walls, supports and adhesion.
Parts that fit the H2D
The Bambu Lab H2D's 350 x 320 mm bed and 325 mm height are what the virtual bed in the viewer shows, so a part that looks too big is too big. Ask for a part to be split into two halves with alignment pins when it does not fit, or for a flat print orientation when it would need supports. The examples above and the library parts below all fit.
Parts that fit the first time
The Bambu Lab H2D prints slightly differently from the next printer, which is why holes come out tight and lids loose. Fit Check cuts a five-minute test slice from the interface that must fit, you report too tight, perfect or too loose, and every model after that is built with the clearance your H2D needs. The test slice downloads free as STL or 3MF. How Fit Check works.
Ready-made parts for the H2D in the library
Bambu Lab H2D build-plate wall rackA wall rack that stores three H2D / 350 mm class build plates on 8 mm lips with 6 mm gaps so the textured side does not scratch.Bambu Lab H2D AMS HT spool restA rest that parks an AMS HT spool (about 200 mm) beside an H2D so a fifth material is not on the floor.Bambu Lab H2D riser feetHeavy-duty riser feet for an H2D (492 × 514 × 626 mm) that lift it 30 mm so the base breathes and a cable can pass underneath.
Questions
Yes. The Bambu Lab H2D is one of the 380+ printers in the slicer catalog, with 4 nozzle variants and the print and filament profiles OrcaSlicer ships for it. Pick it in the download dialog and download a .gcode.3mf; it is saved to your account for next time.
No. SpeakCAD slices on its servers and gives you a .gcode.3mf. Copy it to the H2D's microSD card and start it from the printer's screen, or open it in Bambu Studio and send it over the network. If you prefer your own slicer, download the STL or 3MF instead.
The print profile (layer height and speed presets from the Bambu Lab H2D's profile), the filament profile (the printer's own and the OrcaSlicer library: Generic PLA, PETG, ABS, ASA, TPU, carbon-fibre blends and hundreds of branded filaments), infill, wall count, supports and bed adhesion. Nozzle temperature, bed temperature and speeds come from the profiles you pick.
The virtual bed in the viewer is sized from the Bambu Lab H2D's profile (350 x 320 mm), so you see it before slicing. Ask for the part to be split into two pieces with alignment pins or a dovetail, or for a different orientation; each is one sentence.
Sliced downloads are included in Pro ($9.99 a month, 200 credits) and Unlimited ($24.99 a month); with Starter credits ($5 once for 75 credits, no subscription) a sliced download spends 5 credits on top of the usual 10. Re-slicing a design you already downloaded does not spend the 10 credits again; without Pro or Unlimited each slice still spends 5 credits. STL and 3MF downloads are always available.
Yes. The editor runs in Safari on iPhone and iPad and in Chrome on Android; the file lands in Files or Downloads, ready for the card or the printer's app. The same project opens later on a desktop.
Read more
All 380+ printersEvery printer the slicer has a profile for, by brand.From a phone to the slicerGetting the file from Files or Downloads onto the printer.Exporting to slicersSTL vs 3MF, units, and what the slicer does with the file.The AI 3D editor on your phoneDescribe, render, edit and download from a phone browser.From a ChatGPT description to a filePaste the spec ChatGPT wrote and get the file it could not make.