1
Adapters & couplers
RAM AMPS to GoPro three-prong adapter
This is not a fixed STL. SpeakCAD generates the ram amps to gopro three-prong adapter to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Model an AMPS to GoPro adapter, 50×50×5 mm plate, four 4.3 mm countersunk holes on 30×38 mm, three-prong GoPro mount with 5 mm bolt hole.
What a ram amps to gopro three-prong adapter is
A plate that bolts to the AMPS hole pattern of a RAM round base (four holes on a 30 × 38 mm rectangle) and turns it into a three-prong GoPro mount. The plate is 50 × 50 × 5 mm with 4.3 mm holes for #8 screws, countersunk from the front, and the GoPro prongs are about 3 mm thick with a 5 mm bolt hole. Print flat in PETG or ASA.
The VESA 75 pattern is much larger than AMPS, so it will not line up. Open the ready-made adapter in SpeakCAD for free, change any millimetre in the viewer or the chat, then download the STL.
People also search
amps to gopro adapterram amps gopro mount stlamps plate adapter 3d printram mount gopro adapter
Questions people ask about a ram amps to gopro three-prong adapter
A plate that bolts to the AMPS hole pattern of a RAM round base (four holes on a 30 × 38 mm rectangle) and turns it into a three-prong GoPro mount. The plate is 50 × 50 × 5 mm with 4.3 mm holes for #8 screws, countersunk from the front, and the GoPro prongs are about 3 mm thick with a 5 mm bolt hole. Print flat in PETG or ASA.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Model an AMPS to GoPro adapter, 50×50×5 mm plate, four 4.3 mm countersunk holes on 30×38 mm, three-prong GoPro mount with 5 mm bolt hole.
The VESA 75 pattern is much larger than AMPS, so it will not line up. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More adapters & couplers
Ford F-150 14th gen cup holder tumbler adapterAn adapter that sits in a 2021 or later F-150 console cup holder and holds a big 40 oz tumbler or 1.2 litre bottle upright.Broom handle thread adapter for a mismatched headA short adapter that lets a threaded broom or mop head screw onto a handle with a different thread, saving a perfectly good pole when the head is replaced.Samsung Galaxy Buds 3 Pro adapter insert for AirPods standsA padding insert that lets the Samsung Galaxy Buds 3 Pro case (58.9 x 48.7 x 24.4 mm) sit in stands and docks cut for the AirPods Pro 2 case (60.6 x 45.2 x 2…LoRa 868 MHz antenna mast clip for 25 mm poleA clip that fixes an SMA-mount 868 or 915 MHz LoRa whip antenna to a 25 mm pole so a Meshtastic or Helium node gets height and a clear view.Rode Wireless GO II receiver cold shoe cradleA cradle that fixes a Rode Wireless GO II receiver, which is 44 x 45.3 x 18.5 mm, onto the hot shoe of a Sony A7 IV, Canon EOS R6 or Fujifilm X-T5 without re…Ortlieb Ultimate 6 bar adapter 31.8 mmAn adapter that lets an Ultimate 6 mount clamp a 31.8 mm bar instead of the 25.4 it assumes, 4 mm shim pair.