1
Hobby & gaming
PS5 DualSense dual controller charging stand
A twin-bay stand for two PlayStation 5 DualSense or DualSense Edge controllers (160 x 66 x 106 mm) that holds them face-out with their USB-C ports aligned over two short cables routed through the base. Each bay is a 68 mm wide U-channel with a 3 mm rubber-friendly lip, angled 10 degrees back so the controller rests on its grips, and a 9 x 4 mm slot at the bottom that captures a right-angle USB-C plug with 0.3 mm clearance. Cables exit through a 12 mm hole at the rear of the base. Print it standing on its base with 2 mm walls and no supports. Open the ready-made model free, resize it on your phone or computer, then download a print-ready STL, 3MF or G-code sliced for your printer, free.Opening the ready-made model and downloading it as STL or 3MF are free, no card; AI changes use credits, from Maker at $7.99 a month.No printer? We print this part and ship it to your door. See its priceUpdated
2
Adjust
Change its numbers in the viewer for free, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use 2 credits per request (1 for a quick edit, 3 for a redesign), paid with a plan from Maker at $7.99 a month.3Print
Download a watertight STL or 3MF free, with your numbers and hand edits, or G-code sliced for your printer at the same price. After an AI change the download is included in every plan (4 credits without one).
Dimensions of the ready-made model (editable)
| Parameter | Value |
|---|---|
| overall base length (X) | 190 mm |
| overall base depth (Y) | 90 mm |
| solid base thickness | 6 mm |
| wall thickness | 2 mm |
| inner U-channel width | 68 mm |
| height of slot center above channel floor | 12 mm |
| rear cable exit hole diameter | 12 mm |
| height of rear cable-exit support block | 30 mm |
| thickness (Y) of rear block | 10 mm |
| center X of channel 1 | 55 mm |
| center X of channel 2 | 135 mm |
| cable groove width in base | 6 mm |
| cable groove depth in base | 3 mm |
Example prompt
Design a dual DualSense charging stand 190 x 90 x 80 mm with two 68 mm wide U-channels tilted 10 degrees, a 9 x 4 mm slot in each bay for a right-angle USB-C plug with 0.3 mm clearance, cable channels exiting a 12 mm rear hole, 2 mm walls and a solid 6 mm base.
Fit notes
Off-the-shelf docks rely on proprietary dongles that break. With SpeakCAD you describe your controllers and the exact plug you own, check the stand in the browser without spending anything, add a PS Portal bay or an LED strip groove in the chat, then download the STL.
Questions people ask about a PS5 DualSense dual controller charging stand
A twin-bay stand for two PlayStation 5 DualSense or DualSense Edge controllers (160 x 66 x 106 mm) that holds them face-out with their USB-C ports aligned over two short cables routed through the base. Each bay is a 68 mm wide U-channel with a 3 mm rubber-friendly lip, angled 10 degrees back so the controller rests on its grips, and a 9 x 4 mm slot at the bottom that captures a right-angle USB-C plug with 0.3 mm clearance. Cables exit through a 12 mm hole at the rear of the base. Print it standing on its base with 2 mm walls and no supports.
Click Open it free on this page and create a free account (no card): the ready-made model opens in your browser, on your phone or computer, nothing to install. Change its numbers in the viewer for free and download a watertight STL or 3MF free, or G-code sliced for your printer at the same price. An AI change in the chat uses 2 credits per request (3 for a redesign), and the download after it is included in every plan (4 credits without one). Start with Maker: 50 credits a month for $7.99, cancel anytime.
On this page: open the ready-made model free in a SpeakCAD account (no card), change any dimension in the viewer, then download the STL or 3MF free, or G-code sliced for your printer at the same price.
A shared STL is modelled for someone else's measurements. Here you open the ready-made model free, change it to your measurements in the viewer, then download a file sized for the part you actually own, free as STL or 3MF.
Yes. SpeakCAD slices the part on its servers with OrcaSlicer and your printer's official profile (380+ printers, including Bambu Lab, Prusa, Creality and Elegoo), and you download the G-code (a sliced .gcode.3mf for Bambu Lab printers). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it. Pick your printer on the printers page to see its profile.
No. SpeakCAD runs in the browser on your phone or computer: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL, 3MF or sliced G-code.
Print it your way
More hobby & gaming
Warhammer 40k 32 mm round base movement trayReady-made, opens free. A skirmish movement tray that carries ten Warhammer 40,000 infantry on 32 mm round bases in two ranks of five, so a whole squad of Intercessors or Necron War…Meta Quest 3S Elite strap wall dockReady-made, opens free. A wall dock that holds a Quest 3S with the Elite battery strap hanging on a 40 mm hook and the headset sitting in a 180 mm wide cradle.PlayStation 5 Pro vertical-stand feetReady-made, opens free. A pair of 80 × 40 × 12 mm feet that widen a PS5 Pro vertical stand so it does not rock on carpet.Strymon Iridium pedalboard riserReady-made, opens free. A 15 mm riser for an Iridium so the jacks clear a packed board, 110 × 70 mm.Desk clamp headset hangerReady-made, opens free. A headset hanger clamps to the edge of a desk and holds a gaming headset off the surface where it would otherwise gather cables and crumbs.Nintendo Switch game cartridge case for 24 cardsReady-made, opens free. A slim two-part case with a sliding lid that holds 24 Nintendo Switch game cards in a 6 by 4 grid.