1
Hobby & gaming
Nintendo Switch 2 tabletop stand with USB-C gap
This is not a fixed STL. SpeakCAD generates the nintendo switch 2 tabletop stand with usb-c gap to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create a Switch 2 tabletop stand, 150×90 mm base, 65 degree back, 16 mm deep slot, 20 mm gap under the USB-C port, 3 mm walls.
What a nintendo switch 2 tabletop stand with usb-c gap is
A tabletop stand for the Nintendo Switch 2 (272 × 116 × 13.9 mm with Joy-Con 2 attached) that holds it at 65 degrees with a 16 mm deep slot and leaves a 20 mm gap under the bottom USB-C port so it can charge while playing. The 150 × 90 mm base has TPU feet pockets and 3 mm walls. Print on its side in PETG.
The original Switch has the same 13.9 mm thickness and also fits, but a Switch Lite is much smaller at 208 × 91 mm and sits too low. Open the ready-made stand in SpeakCAD for free, tweak the angle in the viewer or the chat, then download the STL.
People also search
switch 2 stand stlnintendo switch 2 charging stand 3d printswitch 2 tabletop standswitch 2 stand 3d model
Questions people ask about a nintendo switch 2 tabletop stand with usb-c gap
A tabletop stand for the Nintendo Switch 2 (272 × 116 × 13.9 mm with Joy-Con 2 attached) that holds it at 65 degrees with a 16 mm deep slot and leaves a 20 mm gap under the bottom USB-C port so it can charge while playing. The 150 × 90 mm base has TPU feet pockets and 3 mm walls. Print on its side in PETG.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create a Switch 2 tabletop stand, 150×90 mm base, 65 degree back, 16 mm deep slot, 20 mm gap under the USB-C port, 3 mm walls.
The original Switch has the same 13.9 mm thickness and also fits, but a Switch Lite is much smaller at 208 × 91 mm and sits too low. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More hobby & gaming
Steam Deck OLED front-plate standA stand that holds a Deck OLED (about 298 × 117 × 49 mm) by the front plate at 30 degrees so the kickstand is not the only option.Universal controller wall rack for six padsA wall rack for six mixed controllers (DualSense, Xbox, Switch Pro and 8BitDo Ultimate pads) with 34 mm wide arms, 50 mm deep and a 6 mm lip, that fit the ga…Roland SP-404MKII angled standA stand that tilts a Roland SP-404MKII (about 179 × 312 × 76 mm) 15° towards you so the pads and screen are easier to play.Guitar wall hanger with padded yokeA wall hanger lifts a guitar off the floor and out of the way of feet and vacuum cleaners.Pokémon TCG toploader wall display rackA wall rack that shows twelve Pokémon TCG cards in standard 3 x 4 inch toploaders (76 x 102 mm, about 2 mm thick for a 35 pt sleeve) in three rows of four.DJI Neo 2 pocket launch padA 120 mm pad that gives a Neo 2 a clean launch off gravel with 8 mm lips.