1
Organizers & storage
IKEA SKADIS metric hex key holder, 1.5 to 10 mm
This is not a fixed STL. SpeakCAD generates the ikea skadis metric hex key holder, 1.5 to 10 mm to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Model an IKEA SKADIS hex key block, 130×24×22 mm, hex pockets 1.5 to 10 mm plus 0.3 mm, 18 mm deep, embossed sizes, two pegs 40 mm apart.
What a ikea skadis metric hex key holder, 1.5 to 10 mm is
A SKADIS block for a full metric L-key set: 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10 mm. Each key drops short arm up into a hexagonal pocket 0.3 mm larger than its across-flats size, 18 mm deep, with sizes embossed on the front. The block is 130 × 24 × 22 mm and hooks on with two pegs 40 mm apart into the 5 × 15 mm slots. Print it upright in PETG.
Imperial keys (5/64 to 3/8 inch) are close but not identical and will rattle in metric pockets. Open the block in SpeakCAD at no cost, change the sizes in the chat or the viewer, then download the STL.
People also search
skadis allen key holderhex key holder stlallen wrench organizer 3d printikea skadis hex keys
Questions people ask about a ikea skadis metric hex key holder, 1.5 to 10 mm
A SKADIS block for a full metric L-key set: 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10 mm. Each key drops short arm up into a hexagonal pocket 0.3 mm larger than its across-flats size, 18 mm deep, with sizes embossed on the front. The block is 130 × 24 × 22 mm and hooks on with two pegs 40 mm apart into the 5 × 15 mm slots. Print it upright in PETG.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Model an IKEA SKADIS hex key block, 130×24×22 mm, hex pockets 1.5 to 10 mm plus 0.3 mm, 18 mm deep, embossed sizes, two pegs 40 mm apart.
Imperial keys (5/64 to 3/8 inch) are close but not identical and will rattle in metric pockets. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More organizers & storage
Gridfinity 4 × 4 baseplate that fits the Bambu Lab A1 miniA 4 × 4 Gridfinity baseplate, 168 × 168 mm, that prints in one piece on the 180 × 180 mm bed of a Bambu Lab A1 mini.Hex key holder rack for bike workshop toolsA bench or pegboard rack that holds the hex keys, Torx keys and a Park Tool chain tool that every home bike mechanic reaches for: seven graduated hex slots f…Sony NP-FZ100 battery case for four batteriesA pocketable case that holds four Sony NP-FZ100 batteries, the 38.7 x 22.7 x 51.7 mm pack used by the A7 IV, A7 III, A6700 and A1, in labelled bays with a fl…Thru-axle thread-on derailleur-hanger holderA 12 mm dummy axle that holds a spare UDH or brand hanger on the workbench so the threads do not roll into the chip tray.Bosch Click & Go rail hookA hook that snaps onto a Bosch Click & Go rail and holds a tape or knife.CFexpress Type B and SD card walletA hinged wallet for four CFexpress Type B cards (38.5 × 29.8 × 3.8 mm) and four SD cards (32 × 24 × 2.1 mm).