1
Garden & outdoor
Garden hose guide stake with roller
This is not a fixed STL. SpeakCAD generates the garden hose guide stake with roller to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create a hose guide stake, 40 mm roller on 6 mm pin, 70 mm uprights 45 mm apart, cross-section spike 200 mm long, ASA.
What a garden hose guide stake with roller is
A hose guide that stops a dragged hose from flattening the edge of a bed. A 40 mm roller spins on a 6 mm printed pin between two 70 mm tall uprights, and a cross-section spike 200 mm long pushes into the soil. The gap between uprights is 45 mm, so 13 and 19 mm hoses both run through. Print the roller and uprights in ASA or PETG, spike point up.
In stony ground a printed spike can snap; the chat can add a 10 mm hole for a steel rod instead. Open the ready-made guide in SpeakCAD for free, change the gap in the viewer or the chat, then download the STL.
People also search
hose guide stakegarden hose guide stlhose roller guide 3d printhose bed protector
Questions people ask about a garden hose guide stake with roller
A hose guide that stops a dragged hose from flattening the edge of a bed. A 40 mm roller spins on a 6 mm printed pin between two 70 mm tall uprights, and a cross-section spike 200 mm long pushes into the soil. The gap between uprights is 45 mm, so 13 and 19 mm hoses both run through. Print the roller and uprights in ASA or PETG, spike point up.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create a hose guide stake, 40 mm roller on 6 mm pin, 70 mm uprights 45 mm apart, cross-section spike 200 mm long, ASA.
In stony ground a printed spike can snap; the chat can add a 10 mm hole for a steel rod instead. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More garden & outdoor
Plant support clip for 11 mm garden stakesA clip that ties tomato and pepper stems to 11 mm plastic-coated steel garden stakes.Garden tool handle clips for shed railRakes, hoes and spades lean in a corner until a clip system holds them upright by the handle.Greenhouse glazing clipsAluminium greenhouses hold their 3 mm glass panes with W-shaped spring clips and Z-shaped overlap clips that disappear into the lawn every windy winter.Trek Rail Bosch charger holsterA garage holster that parks a Bosch 4A charger and the Rail's charge-port cap on a 4.5 mm hole pair.Apidura Expedition drybag roll clipA clip that keeps an Expedition drybag roll from unrolling, 40 mm jaws with a 2 mm TPU lip.FC-37 rain sensor plate holderA holder that angles an FC-37 or YL-83 raindrop plate (about 54 × 40 mm) at 30 degrees so water runs off and the reading resets after a shower.