1
The prompt on this page opens in SpeakCAD already filled in — after sign-in too. The model renders in your browser. Preview is free.Tools & jigs
Dowel centre-finder set 6, 8 and 10 mm
This is not a fixed STL. SpeakCAD generates the dowel centre-finder set 6, 8 and 10 mm to your millimetres, you adjust it in the chat, then you download and print it.2
Change any millimetre in the chat: wall thickness, hole size, the thing it clips onto. Iterations stay in the tab until it matches what you own.Adjust
3Print
Download a watertight STL or 3MF for 2 credits, drop it in your slicer, and print it. Small fit fixes re-download free.Get it nowThe example prompt comes with you, even through sign-in. Preview is free; a download costs 2 credits.
What a dowel centre-finder set 6, 8 and 10 mm is
Three centre-finders that mark matching dowel holes: 6, 8 and 10 mm bodies with a 1.5 mm centre pin. Each is 20 mm tall. Print in PETG at 0.12 mm so the pin stays sharp.
A nail as a centre punch walks off the dowel. Describe extra sizes in SpeakCAD, preview the set in the browser for free, then download the STL.
Example prompt
Create dowel centre-finders 20 mm tall for 6, 8 and 10 mm dowels, 1.5 mm centre pin, PETG, 0.12 mm layers.
People also search
dowel centre finder stldowel transfer punch 3d print6 8 10 mm dowel markerdowel alignment pins 3d model
Questions people ask about a dowel centre-finder set 6, 8 and 10 mm
Three centre-finders that mark matching dowel holes: 6, 8 and 10 mm bodies with a 1.5 mm centre pin. Each is 20 mm tall. Print in PETG at 0.12 mm so the pin stays sharp.
Click Get it now on this page: the example prompt is filled in for you after you sign in. The model renders in your browser — nothing to install — and previewing is free. Adjust any millimetre in the chat, then export a watertight STL or 3MF for 2 credits when you want to print.
Start from this working example and replace any number with what you measured: Create dowel centre-finders 20 mm tall for 6, 8 and 10 mm dowels, 1.5 mm centre pin, PETG, 0.12 mm layers.
A nail as a centre punch walks off the dowel. In SpeakCAD you generate and preview for free, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More tools & jigs
Fairphone 5 modular repair standA bench stand that holds a Fairphone 5 (about 162 × 76 × 9.6 mm) face-down at 20 degrees so you can swap the battery, cameras or USB-C port without the phone…20 mm bench dog for Festool MFTA 20 mm bench dog 25 mm tall with a 0.1 mm taper so it drops into an MFT/3 hole and a 6 mm through-hole for a hold-down.Shimano flat-mount bleed blockA block that keeps Shimano flat-mount pistons from popping out during a bleed, 22 × 10 × 8 mm.Makita MAKPAC Type 1 bit caddyA caddy that fills a MAKPAC Type 1 (about 395 × 295 × 70 mm) with 40 impact bits on 7 mm rails.Pocket-hole drilling jig blockThis jig guides a stepped 9.5 mm pocket-hole bit at the standard 15 degree angle into the edge of 18 mm sheet goods, for pocket-screw cabinet joints without…Labeled socket organizer railLoose sockets in a drawer cost minutes on every job; a rail with sized posts keeps a 1/2 inch drive set in order and shows the size on each post.