Nine CAD mistakes beginners make on their first printed parts, and the number that fixes each
A hole the size of its screw, zero clearance, 0.8 mm walls, text too small: the nine first-part mistakes, and the number that fixes each.The first part you design almost works. The screw does not go through, the lid does not go on, a wall snaps. None of it is the CAD's fault or the printer's: each is one number a beginner has no reason to know yet. Here are the nine we see most, with the number.
1. A hole the size of its screw
You draw a 3 mm hole for an M3 screw, and it does not go in. Printed holes come out 0.2 to 0.4 mm small, because each layer's outline bulges inward a little.
The number: a clearance hole for M3 is 3.4 mm (M4 4.5, M5 5.5). For a screw that should bite into the plastic, smaller: M3 2.5 mm. SpeakCAD's Hole presets are these sizes, with a tap toggle for the second kind. Add a hole to an STL.
2. Zero clearance between parts that fit together
A lid drawn exactly the size of the box, a peg exactly the size of its hole. They will not go together.
The number: 0.1 to 0.2 mm for a press fit, 0.4 to 0.6 mm for a sliding fit, per side. Your printer is not average, so for a fit that matters print a test first: Fit Check cuts a five-minute slice of just the fit. Tolerances and clearances.
3. Walls too thin
A 0.8 mm wall looks fine on screen and prints as two flimsy lines, or not at all.
The number: at least 1.2 mm (three lines of a 0.4 mm nozzle); 1.6 mm for a case on a desk, 2 mm for one that gets dropped or screwed to a wall. Wall thickness.
4. Measuring once, with a ruler
The part is 1.5 mm too small because the ruler said 42 and the object is 43.5 at its widest.
The number: measure with callipers, at the widest point, twice, and write each size down with what it is. A ruler is fine for a size that does not have to fit. How to measure an object for a printed part.
5. Overhangs the printer cannot print
A shelf sticking straight out of a wall, a T-shape standing up: the printer lays plastic on air.
The number: keep overhangs under 45°, and give the part a flat face to sit on the bed. Turn the part before adding supports: the same bracket printed on its side often needs none. Why does my print need supports?
6. Sharp inside corners where it takes load
The bracket snaps exactly at the inside of the bend, where all the stress meets in a sharp corner.
The number: a fillet of 2 to 3 mm inside a bend that carries weight. And print it so the layers run along the load, not across it: a bracket printed standing up breaks between layers.
7. Text too small or too shallow
The label reads as a smudge.
The number: letters 5 mm tall or more with a 0.4 mm nozzle, 0.6 mm deep (raised or engraved). 6 mm tall and 0.6 mm deep is SpeakCAD's Text tool's starting point. Add text to a print.
8. Big horizontal holes that sag
A 20 mm hole through the side of a part prints with a droopy top, because the top of the circle is a bridge in the air.
The number: up to about 8 mm across, a horizontal hole prints acceptably; bigger, turn the part so the hole is vertical, or make its top pointed (a "teardrop") so it prints as a 45° overhang instead of a flat bridge.
9. Printing the whole part to test it
Three hours of print to find out the lid is 0.2 mm tight, then three more.
The number: five minutes. Print only the part of the model that must fit, a thin slice through the lid's edge or the hole for the magnet, and adjust before the long print. That is what Fit Check does, and it remembers the clearance your printer needs for every model after.
The shortcut
Most of these numbers are defaults in SpeakCAD: the hole presets are clearance sizes, walls suit a 0.4 mm nozzle, the AI applies the clearance when you say "press fit" or "sliding fit", and every part starts from a shape with a flat base. You still have to measure the thing it fits, and that part is yours. The glossary explains the words above, and CAD for beginners has a first week of parts that teaches them in order.
Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.
Prompts to start from
Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.A box 80 x 50 x 30 mm outside with 2 mm walls and a lid that slides on with 0.4 mm clearance
A plate 60 x 40 x 4 mm with two M3 holes for screws that cut their own thread, 40 mm apart, and a 6 mm pocket 2.2 mm deep for a press-fit 6 x 2 mm magnet
An L bracket 50 x 50 mm, 25 mm wide, 4 mm thick, 3 mm fillet inside the bend, two M4 clearance holes on each leg
Questions
Printed holes come out 0.2 to 0.4 mm smaller than drawn. Design a clearance hole a little bigger than the screw: 3.4 mm for M3, 4.5 mm for M4, 5.5 mm for M5. For a screw that cuts its own thread, use the smaller tapping size, 2.5 mm for M3.
0.1 to 0.2 mm per side for a press fit, 0.4 to 0.6 mm for a sliding fit. Print a small test of the fit first, because each printer is a little different.
1.2 mm with a 0.4 mm nozzle (three lines). 1.6 mm suits a case that sits on a desk and 2 mm one that is dropped or screwed to a wall.