1
Garden & outdoor
Trellis netting clip for 16 mm stakes
This is not a fixed STL. SpeakCAD generates the trellis netting clip for 16 mm stakes to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design a trellis netting clip, 16.3 mm stake bore with 13.5 mm snap opening, flat 20 mm front hook for 3 mm net strands, PETG.
What a trellis netting clip for 16 mm stakes is
A clip that holds climbing plant netting or pea mesh on 16 mm garden stakes. It snaps around the stake through a 13.5 mm opening into a 16.3 mm bore and a flat 20 mm hook on the front catches the net strands up to about 3 mm thick. Printed in pairs per stake, they keep the net taut. Print flat in PETG or ASA.
Thin 8 mm stakes are too narrow for this bore. Open the clip in SpeakCAD for free, adjust the hook in the viewer or the chat, then download the STL.
People also search
trellis netting clipsplant net clip stlgarden netting clip 3d printpea netting stake clip
Questions people ask about a trellis netting clip for 16 mm stakes
A clip that holds climbing plant netting or pea mesh on 16 mm garden stakes. It snaps around the stake through a 13.5 mm opening into a 16.3 mm bore and a flat 20 mm hook on the front catches the net strands up to about 3 mm thick. Printed in pairs per stake, they keep the net taut. Print flat in PETG or ASA.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design a trellis netting clip, 16.3 mm stake bore with 13.5 mm snap opening, flat 20 mm front hook for 3 mm net strands, PETG.
Thin 8 mm stakes are too narrow for this bore. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More garden & outdoor
Suet cake feeder cageA hanging cage for a standard suet cake, about 114 × 114 × 38 mm.Garden hose nozzle holster for postSpray nozzles left on the lawn get run over by the mower; a holster on a fence post keeps one at hand next to the tap.Tent guy line tensioner for 3 mm reflective cordA three-hole line tensioner for the 2 to 3 mm reflective guy cord used on MSR, Big Agnes, Nemo and Decathlon Quechua tents, replacing the sliders that snap i…Brompton C Line front-carrier block coverA cover that keeps grit out of a C Line front-carrier block when the bag is off, 40 × 30 × 15 mm with a 2 mm snap.Jetboil Flash 2.0 pot-support ringA ring that lets a Flash 2.0 hold a non-Jetboil 1 L pot, 110 mm ID with three 8 mm tabs.Gardena hose end parking clip for 13 mm hoseA wall clip that parks the end of a 13 mm (1/2 inch) garden hose, which is about 19 mm outside, next to the tap.