1
Hobby & gaming
PlayStation Portal desk stand with cable channel
A stand for the PlayStation Portal remote player that supports the grips on either side of its 8 inch screen and tilts it back 20 degrees for a bedside or desk view. The Portal is a little over 300 mm wide, so the stand uses two independent 60 mm wide saddles with 0.5 mm clearance joined by a 200 mm bridge, leaving the centre section of the device untouched. Its USB-C port sits low on the underside, so a 14 mm channel in the base lets a cable run out the back for charging while it rests. Print the stand on its base with 2 mm walls; the saddles have 3 mm fillets that will not mark the plastic. Open the ready-made model free, resize it on your phone or computer, then download a print-ready STL, 3MF or G-code sliced for your printer, free.Opening the ready-made model and downloading it as STL or 3MF are free, no card; AI changes use credits, from Maker at $7.99 a month.No printer? We print this part and ship it to your door. See its priceUpdated
2
Adjust
Change its numbers in the viewer for free, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use 2 credits per request (1 for a quick edit, 3 for a redesign), paid with a plan from Maker at $7.99 a month.3Print
Download a watertight STL or 3MF free, with your numbers and hand edits, or G-code sliced for your printer at the same price. After an AI change the download is included in every plan (4 credits without one).
Dimensions of the ready-made model (editable)
| Parameter | Value |
|---|---|
| total length | 320 mm |
| total depth | 100 mm |
| width of each saddle | 60 mm |
| depth of each saddle | 50 mm |
| per side | 0.5 mm |
| wall thickness | 2 mm |
| fillet radius | 3 mm |
| how tall the slot cut is (grips edge) | 22 mm |
| height of saddle block above base | 34 mm |
| length of bridge between saddle inner faces... (span) | 200 mm |
| bridge cross-section height | 14 mm |
| base thickness (floor) hosting cable channel | 8 mm |
| channel diameter | 14 mm |
Example prompt
Model a PlayStation Portal desk stand 320 x 100 x 60 mm with two 60 mm wide grip saddles 50 mm deep and 0.5 mm clearance joined by a 200 mm bridge, 20 degree back tilt, a 14 mm USB-C cable channel through the base exiting at the rear, 3 mm fillets and 2 mm walls.
Fit notes
Because the Portal has almost no third-party accessories, a generated part is the fastest way to a proper stand. In SpeakCAD you describe grip width and lean angle, review the model in the browser, and download the STL once you have refined it in the chat.
Questions people ask about a PlayStation Portal desk stand with cable channel
A stand for the PlayStation Portal remote player that supports the grips on either side of its 8 inch screen and tilts it back 20 degrees for a bedside or desk view. The Portal is a little over 300 mm wide, so the stand uses two independent 60 mm wide saddles with 0.5 mm clearance joined by a 200 mm bridge, leaving the centre section of the device untouched. Its USB-C port sits low on the underside, so a 14 mm channel in the base lets a cable run out the back for charging while it rests. Print the stand on its base with 2 mm walls; the saddles have 3 mm fillets that will not mark the plastic.
Click Open it free on this page and create a free account (no card): the ready-made model opens in your browser, on your phone or computer, nothing to install. Change its numbers in the viewer for free and download a watertight STL or 3MF free, or G-code sliced for your printer at the same price. An AI change in the chat uses 2 credits per request (3 for a redesign), and the download after it is included in every plan (4 credits without one). Start with Maker: 50 credits a month for $7.99, cancel anytime.
On this page: open the ready-made model free in a SpeakCAD account (no card), change any dimension in the viewer, then download the STL or 3MF free, or G-code sliced for your printer at the same price.
A shared STL is modelled for someone else's measurements. Here you open the ready-made model free, change it to your measurements in the viewer, then download a file sized for the part you actually own, free as STL or 3MF.
Yes. SpeakCAD slices the part on its servers with OrcaSlicer and your printer's official profile (380+ printers, including Bambu Lab, Prusa, Creality and Elegoo), and you download the G-code (a sliced .gcode.3mf for Bambu Lab printers). G-code sliced for your printer costs the same as the STL: included in every plan, free for a part you shaped by hand, 4 credits without a plan for a part with AI work in it. Pick your printer on the printers page to see its profile.
No. SpeakCAD runs in the browser on your phone or computer: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL, 3MF or sliced G-code.
Print it your way
More hobby & gaming
Steam Deck 2 travel-dock cable blockReady-made, opens free. A block that holds a USB-C hub and the Deck 2 charger in a 160 × 80 × 30 mm travel case with 0.4 mm clearance.Dice tower with catch trayReady-made, opens free. A dice tower randomises rolls and keeps dice from flying off the table, which matters when a game night involves drinks and miniatures.RC car shock tower braceReady-made, opens free. A shock tower brace spans the two upper shock mounts and stops the towers flexing or snapping during hard landings.Steam Deck OLED dock stand with USB-C cutoutReady-made, opens free. A desk stand that holds a Steam Deck OLED (298 x 117 x 49 mm) at a 15 degree lean while a USB-C hub or the official dock's cable stays plugged into the top p…Pokémon TCG toploader wall display rackReady-made, opens free. A wall rack that shows twelve Pokémon TCG cards in standard 3 x 4 inch toploaders (76 x 102 mm, about 2 mm thick for a 35 pt sleeve) in three rows of four.Toniebox 2 wall shelf with Tonie pegsReady-made, opens free. A 220 mm shelf that holds a Toniebox 2 and six Tonies on 8 mm pegs.