1
Hobby & gaming
Mooer micro pedal double riser
This is not a fixed STL. SpeakCAD generates the mooer micro pedal double riser to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Create a double riser for two Mooer micro pedals, two 43×94.5 mm recesses 1 mm deep, 4 mm gap, 18 mm high, open underneath.
What a mooer micro pedal double riser is
A riser that holds two Mooer micro pedals (93.5 × 42 × 52 mm each) side by side and 18 mm higher than the row in front. The top has two 43 × 94.5 mm recesses 1 mm deep for hook-and-loop, a 4 mm gap between them for the jacks, and the underside is open for patch cables. The riser is 92 × 98 mm. Print upside down in PETG.
A Boss compact pedal is 73 × 129 mm and will not fit the recesses. Open the ready-made model in SpeakCAD for free, change the pedal count or any millimetre, then download the STL.
People also search
mooer micro pedal riser stlmini pedal riser 3d printmooer pedal risermicro pedal pedalboard riser
Questions people ask about a mooer micro pedal double riser
A riser that holds two Mooer micro pedals (93.5 × 42 × 52 mm each) side by side and 18 mm higher than the row in front. The top has two 43 × 94.5 mm recesses 1 mm deep for hook-and-loop, a 4 mm gap between them for the jacks, and the underside is open for patch cables. The riser is 92 × 98 mm. Print upside down in PETG.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Create a double riser for two Mooer micro pedals, two 43×94.5 mm recesses 1 mm deep, 4 mm gap, 18 mm high, open underneath.
A Boss compact pedal is 73 × 129 mm and will not fit the recesses. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More hobby & gaming
Pedalboard patch bay jack plateA patch bay for the edge of a pedalboard so you plug the guitar and amp into the board instead of the first and last pedal.Model kit sprue cutter holder and parts trayBuilding plastic model kits means dozens of tiny parts and a few sharp tools that roll off the bench.Xbox Elite Series 2 controller display standA display stand for the Xbox Elite Series 2 controller that shows off its rubberised grips and paddles while keeping it within reach of the console.WLED hex-panel stand for six cellsA stand that holds a six-cell WLED hex (about 300 mm across) at 15 degrees with a 20 mm USB-C well in the base.Flydigi Vader 4 Pro display standA stand that holds a Vader 4 Pro at 25 degrees with the RGB face visible and a 14 mm USB-C slot.Nintendo Switch 2 tabletop stand with USB-C gapA tabletop stand for the Nintendo Switch 2 (272 × 116 × 13.9 mm with Joy-Con 2 attached) that holds it at 65 degrees with a 16 mm deep slot and leaves a 20 m…