1
Garden & outdoor
FC-37 rain sensor plate holder
This is not a fixed STL. SpeakCAD generates the fc-37 rain sensor plate holder to your millimetres, you adjust it in the chat, then you download and print it.Building the 3D preview…
2
Adjust
Click a part and change its numbers in the viewer, or ask the AI in the chat: wall thickness, hole size, the thing it clips onto. AI changes use plan credits.3Print
Download a watertight STL or 3MF with a Maker or Pro plan, drop it in your slicer, and print it. Small fit fixes re-download free.
Get it nowOpening the ready-made model is free. A plan covers AI changes and the download.
Example prompt
Design an FC-37 rain sensor holder, 55×41 mm frame with 1.5 mm ledge at 30 degrees, closed board pocket, 20 mm post with cable-tie slot, ASA.
What a fc-37 rain sensor plate holder is
A holder that angles an FC-37 or YL-83 raindrop plate (about 54 × 40 mm) at 30 degrees so water runs off and the reading resets after a shower. The frame is 55 × 41 mm with a 1.5 mm ledge, a closed pocket behind it holds the comparator board, and a 20 mm post clamps to a railing with a cable tie. Print in ASA or PETG, 2 mm walls.
A flat-mounted plate stays wet for hours. Open the ready-made holder in SpeakCAD for free, set the angle in the chat or the viewer, then download the STL.
People also search
rain sensor holder stlfc-37 rain sensor mount 3d printyl-83 raindrop sensor caserain sensor module bracket 3d model
Questions people ask about a fc-37 rain sensor plate holder
A holder that angles an FC-37 or YL-83 raindrop plate (about 54 × 40 mm) at 30 degrees so water runs off and the reading resets after a shower. The frame is 55 × 41 mm with a 1.5 mm ledge, a closed pocket behind it holds the comparator board, and a 20 mm post clamps to a railing with a cable tie. Print in ASA or PETG, 2 mm walls.
Click Get it now on this page and sign in: you can open the ready-made model for free, and the example prompt is filled in if you want the AI to redesign it. The model renders in your browser, nothing to install. Change any millimetre in the viewer or the chat (AI changes use plan credits), then export a watertight STL or 3MF with a Maker or Pro plan when you want to print.
Start from this working example and replace any number with what you measured: Design an FC-37 rain sensor holder, 55×41 mm frame with 1.5 mm ledge at 30 degrees, closed board pocket, 20 mm post with cable-tie slot, ASA.
A flat-mounted plate stays wet for hours. In SpeakCAD you open the ready-made model for free, change it to your measurements, then download a file sized for the part you actually own.
No. SpeakCAD runs entirely in the browser: the chat, the 3D engine and the live viewer load in the tab. The only file you download is the finished STL or 3MF.
More garden & outdoor
Raised bed corner connectorTimber raised beds are quickest to build when the boards slot into corner connectors instead of being screwed at awkward angles.Compost aerator tool headA compost heap breaks down faster when air gets into the middle, and this aerator head turns a broom handle into a plunging turner.Tent stake puller hook for MSR Groundhog stakesA palm-sized hook that slides under the notched head of an MSR Groundhog, Mini Groundhog or any Y-beam stake and pulls it out of packed ground without bendin…Cowboy Cruiser ST phone-pad riserA 15 mm riser under a Cowboy phone pad so a MagSafe case still sits flush on the stem.Hammerhead Karoo 3 out-front mountAn out-front for a Karoo 3 on 31.8 mm bars with the official 4-hole pattern and a 20 mm GoPro boss.Black Diamond Spot 400 helmet clipA clip that puts a Spot 400 on a vented helmet without the official kit, 18 mm vent snap and a 25 mm lamp saddle.