Own a 3D printer but not the CAD skills? Parts you can make tonight

The best 3D prints for the workshop and garage in 2026 (with the prompts)

Eleven workshop prints sized to your tools: holders, socket trays, drill guides, shims, hooks, dust-port adapters and labels, each with what to measure.
17 November 2026 · 7 min readworkshopgarageprompts

The best workshop prints are sized to one tool, one hose or one gap that you measure once: a holder cut for your drill, a tray whose pockets match your sockets, an adapter between the two diameters your sander and your hose happen to have. Here are 11, each with the measurement that decides the fit and a prompt for SpeakCAD. Most belong in PETG rather than PLA: a garage gets hot in summer, and tools get dropped on things.

The short answer

  • Print first: holders sized to the tools you reach for most.
  • The one no shop sells: the dust-port adapter.
  • Quickest: spacers, shims and label plates, shaped with the hand tools, free.
  • Buy instead: anything that lifts, guards a blade or holds weight above a person. A printed part is not a rated part.

1. A wall holder for the cordless drill

Measure: the width of the grip just under the motor (45 mm here; measure yours). The slot is 1 mm wider.

A wall holder for a cordless drill: a shelf 90 mm wide, 70 mm deep and 5 mm thick with a slot 46 mm wide and 60 mm deep open at the front for the grip, a 45 degree gusset under each side, and a back plate with three countersunk holes for 4 mm screws

Look elsewhere if you want rows of tools you can rearrange: Gridfinity, Skådis or a French cleat compares the wall systems.

2. A rack for the screwdrivers

Measure: the thickest shaft (the hole is that plus 1 mm) and the widest handle (the spacing is that plus 5 mm).

A wall rack for six screwdrivers: a shelf 200 x 40 mm and 6 mm thick with six 9 mm holes 32 mm apart, each with a 7 mm slot to the front edge, a back plate 30 mm tall with two countersunk holes for 4 mm screws, and a gusset at each end

Look elsewhere if the wall is a pegboard: measure its holes and print the hook from the 20 useful prints list.

3. A socket tray with the sizes on it

Sockets are wider than the size stamped on them. Measure: each one's outside diameter with a calliper; each pocket is about 1 mm wider.

A socket tray 180 x 45 x 14 mm with eight round pockets 10 mm deep in a row, 12.5, 13, 14, 15.5, 17, 18.5, 20 and 23 mm across, 3 mm between pockets, and the socket size engraved 0.6 mm deep in front of each pocket in digits 6 mm tall

Look elsewhere if the drawer has a Gridfinity plate: make it a Gridfinity bin that locks into the grid.

4. A drill guide for straight holes

Measure: the bit. The bore is the bit plus 0.4 mm, so it turns freely.

A drill guide block 50 x 50 x 30 mm with a 6.4 mm vertical hole through its centre for a 6 mm bit, a V groove 8 mm deep across the underside so it sits on a round tube, and a sight notch at the centre of each side

Look elsewhere if you drill hundreds of holes: plastic wears and the bore opens up. Buy a steel guide.

5. A jig that repeats a hole spacing

Measure: the spacing you are matching, from the left edge of one hole to the left edge of the next.

A drilling jig for drawer handles: a plate 140 x 40 mm and 5 mm thick with two 4.4 mm guide holes 96 mm apart, a fence 15 mm tall along one long edge that hooks over the top of the drawer front, and a notch at the centre of the fence

6. Spacers and shims

One to shape by hand, free: the Cylinder shape with your diameter and height typed in, then Hole with a screw preset. Measure: the gap, with a calliper, and ask for a thickness your layers can make: with 0.2 mm layers, 1.4 mm prints true and 1.5 mm does not.

A set of five shims side by side, each 40 x 20 mm with a 5.5 mm slot open to one short edge for an M5 bolt, 0.6, 1, 1.4, 2 and 3 mm thick

Look elsewhere if it is squeezed hard between metal parts for years: plastic creeps under a steady load. Use a steel washer.

7. Hooks for the extension lead and the vacuum hose

Measure: how thick the coiled bundle is; the arm is that plus 20 mm. Make it 4 mm thick or more, with a fillet where the arm meets the plate, and print it lying on its side so the layers run along the arm.

A wall hook for a coiled extension lead: an arm 90 mm long, 30 mm wide and 6 mm thick with a 25 mm upturned tip, a 3 mm fillet where it meets a back plate 60 x 80 mm, and two countersunk holes for 5 mm screws 50 mm apart, printed lying on its side

Look elsewhere if it is a full garden hose: several kilos on layer lines, in the sun. Buy the steel hanger.

8. A tray for loose batteries

An AA cell is about 14.5 mm across and 50.5 mm long, so a 15.5 mm pocket holds one upright. Measure: any other cell.

A tray for twelve AA batteries standing up: three rows of four round pockets 15.5 mm across and 20 mm deep, 2 mm between pockets, 1.6 mm outer walls, rounded corners

Look elsewhere if you want a wall mount for power-tool batteries: each brand's battery slides onto its own rail, and a published model already tested on it is the quicker route. You can still add screw holes or a label to it.

9. A dust-port adapter between two measured diameters

Measure: the outside of the tool's port and the inside of the hose cuff, each at the mouth and 20 mm in, because both taper.

A dust-port adapter: one end slips over a tool port 35.2 mm across (inside 35.6 mm, 30 mm long), the other pushes into a hose cuff 31.5 mm inside (outside 31.2 mm, 35 mm long, tapering by 0.5 mm), 2.5 mm walls, and a smooth cone 20 mm long between them

Print a test ring first: Fit Check cuts a five-minute slice of each end.

10. Label plates for bins and shelves

By hand, free: the Plate shape, then Text, up to 40 characters in one bold font. Letters 5 mm tall or more read cleanly with a 0.4 mm nozzle, and a filament change at the layer where raised letters start gives two colours. Measure: the front of the bin.

A label plate 80 x 25 x 2 mm with rounded corners, the words M6 BOLTS raised 0.8 mm in letters 10 mm tall, and a 3.4 mm hole 6 mm from each short end

Look elsewhere if the labels change every month: a label printer is quicker.

11. Soft jaws for the vice

Measure: the width and the height of the steel jaws. Magnets hold the covers on: a 6 mm round magnet presses into a 6.2 mm pocket.

A pair of vice soft jaws for steel jaws 100 mm wide and 20 mm tall: each an L shape 100 mm long with a face 8 mm thick and a top lip 15 mm deep, a V groove 3 mm deep along the face for round stock, and two pockets 6.2 mm across and 2.2 mm deep in the back for 6 x 2 mm magnets

How we picked

  1. Does it fit one tool, hose or gap of yours? If any size will do, download it.
  2. Will plastic survive the job? Holders, trays, guides and adapters: yes. Lifting, hard clamping and guarding: no.
  3. Does it print without supports? Flat on its back or lying on its side.

Printing for a workshop

Three or more walls for anything with screws, four or five for hooks and brackets, and the load along the layers (how to make printed parts stronger). The filament comparison says when ASA is worth it; the print time calculator gives the print time on your printer.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

Prompts to start from

Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.

A wall holder for a cordless drill: a shelf 90 mm wide, 70 mm deep and 5 mm thick with a slot 46 mm wide and 60 mm deep open at the front for the grip, a 45 degree gusset under each side, and a back plate with three countersunk holes for 4 mm screws

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A socket tray 180 x 45 x 14 mm with eight round pockets 10 mm deep in a row, 12.5, 13, 14, 15.5, 17, 18.5, 20 and 23 mm across, 3 mm between pockets, and the socket size engraved 0.6 mm deep in front of each pocket in digits 6 mm tall

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A dust-port adapter: one end slips over a tool port 35.2 mm across (inside 35.6 mm, 30 mm long), the other pushes into a hose cuff 31.5 mm inside (outside 31.2 mm, 35 mm long, tapering by 0.5 mm), 2.5 mm walls, and a smooth cone 20 mm long between them

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

Questions

Parts sized to your own tools: a wall holder for the drill, a rack for the screwdrivers, a socket tray with measured pockets, drill guides and spacing jigs, spacers and shims, hooks for leads and hoses, a dust-port adapter between two measured diameters, and label plates. Each depends on one measurement that a downloaded file cannot know.

Measure the outside diameter of the tool's port and the inside diameter of the hose cuff with a calliper, at the mouth and 20 mm in, because both taper. Make the end that slips over the port about 0.4 mm larger than it and the end that pushes into the cuff about 0.3 mm smaller, with 2.5 mm walls and a cone between them, and print a short test ring of each end first.

PETG for most of them. It is tougher than PLA, bends before it breaks and takes more heat, which matters in a garage in summer. PLA is fine for trays, labels and jigs that stay indoors, and ASA is the choice for parts left in the sun.

For a job, yes: a printed guide block holds a bit square, and a jig repeats a hole spacing to a few tenths of a millimetre. Make the bore about 0.4 mm larger than the bit so it turns freely. Plastic wears, so for hundreds of holes buy a steel guide or press a steel bushing into the print.

Make your first part tonight

No CAD, no tutorial. Type what you need on your phone or laptop, watch it render, and send the STL to your slicer. Try the live demo first, no account; your own part starts with Maker at $7.99 a month, cancel anytime.