How to design cable clips and cable management for 3D printing in 2026
Measure the cable, pick the clip type, size the bore and the opening, lay the clip on its side so it bends without snapping, and choose PLA or PETG.To design a cable clip that works, measure the cable's diameter with a calliper, choose the clip type from how often the cable comes out, and size the bore from the fit you want: 0.3 mm under the diameter to grip the cable, about 1 mm over it to let it slide. Then print the clip lying on its side, so the arms bend along the layers instead of across them, and use PETG for any clip that flexes more than once.
The short answer
- Measure the cable's jacket in two directions, and the plug if it has to pass through.
- Pick the type from how often the cable comes out and what the clip fixes to: the table below has seven.
- Bore: 0.3 mm under the cable to grip, 1 mm over to slide, 2 mm over for a loose bundle.
- Opening of a C clip: about 1 mm narrower than the cable.
- Orientation: the C shape flat on the bed.
- Material: PETG for anything that flexes, PLA for saddles, trays and feet that do not.
Step 1: measure the cable
Close the calliper until the jaws just touch the jacket: a soft cable squashes. Measure twice, at right angles, because many cables are oval or flat. A phone charging cable may be 3 to 4 mm and a mains lead 6 to 8 mm, but brands differ: measure yours.
Then measure what the clip fixes to: the thickness of the desk edge for a clamp, the screw for a saddle (a 4 mm wood screw goes through a 4.5 mm hole), or the flat area for a tape pad. And look at the plug. A USB-C plug with its shell is about 12 x 7 mm, so no charging cable threads through a closed 4 mm ring: that is why clips have openings. How to measure for a printed part covers the calliper.
Step 2: pick the clip type
| Type | Best for | The cable comes out | Fixed with | Has to flex |
|---|---|---|---|---|
| Open C clip | One cable at a desk edge | Every day | A screw or tape | Each time |
| Closed clip with a slot | A cable that must not fall out | Rarely | A screw | Once, when fitted |
| Screw-down saddle | A heavy lead along a wall or under a desk | Only with a screwdriver | One or two screws | No |
| Adhesive-base clip | Glass, metal, a rented desk | Every day | Double-sided tape on a pad of about 20 x 20 mm | Each time |
| Comb | Several cables, kept in order | Often | Screws or a clamp | A little |
| Under-desk tray | Power bricks and slack | Rarely | Screws | No |
| Cable-box feet | Lifting a box that hides a power strip | Never | Clipped to the box wall | No |
A closed clip with a slot is a ring with a narrow cut through it: you flex the ring open once to push the cable in, and it cannot fall out on its own. Cable-box feet lift the box so the cables leave underneath and air gets in: measure the thickness of the box's wall and ask for feet that clip onto it.
Step 3: size the bore and the opening
The numbers come from the tolerances guide, applied to a soft cable instead of a hard shaft.
| The cable should | Bore | Why |
|---|---|---|
| Stay where you put it | Diameter minus 0.3 mm | The jacket gives, and the clip squeezes it lightly |
| Slide through | Diameter plus about 1 mm | A sliding fit is 0.4 to 0.6 mm per side |
| Lie loose with others | Diameter plus 2 mm or more | A loose fit is 0.8 mm or more per side |
The rest of the clip:
- Opening of a C clip: about 1 mm narrower than the cable (5 mm for a 6 mm cable), with a 45° lead-in on both lips.
- Slot of a closed clip: about half the cable's diameter.
- Arms: 1.6 to 2 mm thick, so they spring. Thicker arms grip harder and crack sooner.
- Base: 2 to 3 mm thick, and the clip 10 to 15 mm wide.
- A comb: fingers at least 2 mm wide between the slots.
Step 4: lay it down so it bends without snapping
A printed part is a stack of layers, and the bond between layers is weaker than the plastic along a layer. A clip arm has to bend, so the layers must run along the arm.
- Right: the C shape flat on the bed, the cable's direction pointing up. Each layer is a complete C, and opening the clip bends every layer along its length.
- Wrong: the base flat on the bed and the C standing up like an arch. The arms are then stacks of small layers, and the clip snaps along a layer line, often the first time it is opened.
The trap is the adhesive-base clip: base down looks like the obvious way to print it, and it is the weak one. Lay it on its side. A screw hole through the base then prints lying down, which is fine up to about 8 mm across. Saddles, trays and feet do not flex, so print them whichever way needs no supports. A tray longer than the bed prints in two halves joined by pins.
Step 5: PLA or PETG
- PLA is stiff and precise, and it snaps instead of bending: a thin PLA clip that has to flex cracks after a few uses. It also softens at around 55 to 60 °C. Use it for saddles, trays and feet, indoors and away from heat.
- PETG is tougher and a little flexible: it bends before it breaks, and it takes about 70 to 80 °C. Use it for C clips, closed clips with a slot, combs, and anything behind a computer, next to a power brick or near a radiator.
- TPU is for a strap that wraps a bundle, where the part should bend all the way round.
Three walls or more make a clip arm solid plastic, so infill does not matter there. PLA, PETG, ABS or ASA compares the materials in full.
Step 6: describe it, test it, print the row
Type the clip into SpeakCAD with the cable's diameter, the fit you want and how it fixes:
Before a row of ten, print one: Fit Check cuts a five-minute slice of the opening and the bore to hold against the real cable, and a clip that is too tight is a small change ("open the bore 0.2 mm"). A saddle is also a part to shape by hand, free: a box 36 x 12 x 9 mm, a rectangle 7 mm wide and 7 mm tall Cut through the long side with its centre 3.5 mm above the bottom edge, and an M4 Hole through the top at each end.
When not to design it
If any size will do, a bag of adhesive clips from a shop is quicker than a print. Design the clip when the cable is an odd size, when several have to sit in a set order, or when it fixes to something only your desk has. The desk setup list has the parts that go with it.
Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.
Prompts to start from
Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.A C clip for a 6 mm cable that screws under a desk: a 5.7 mm bore, a 5 mm opening with 45 degree lead-ins, arms 1.8 mm thick, 12 mm wide, on a base 30 x 12 mm and 3 mm thick with one countersunk hole for a 4 mm screw, printed lying on its side
A cable comb for the back edge of a desk: a strip 120 x 20 mm and 3 mm thick with five round slots for cables of 4, 4, 5, 6 and 8 mm, each opening 1 mm narrower than its cable, fingers at least 2 mm wide, and two countersunk holes for 4 mm screws
An under-desk cable tray 400 mm long with a channel 60 x 40 mm and 2 mm walls, open at the top and both ends, slots in the floor for air, screw tabs every 100 mm, split into two 200 mm halves joined by 6 mm pins with 0.2 mm clearance
Questions
It depends on the fit. To grip the cable so it stays put, make the bore 0.3 mm smaller than the cable's diameter. To let it slide, about 1 mm larger (a sliding fit is 0.4 to 0.6 mm per side). For a loose bundle, 2 mm or more. The opening of a C clip is about 1 mm narrower than the cable, with a 45 degree lead-in on both lips.
Lying on its side, with the C shape flat on the bed, so every layer is a complete C and the arms bend along the layers. A clip printed base down, with the C standing up, has arms made of stacked layers and snaps along a layer line, often the first time it is opened.
PETG for any clip that has to flex: it is tougher, bends before it breaks and takes about 70 to 80 °C. PLA is stiff and snaps instead of bending, and it softens at around 55 to 60 °C, so keep it for saddles, trays and feet that do not flex and stay away from heat.
With a calliper, closing the jaws until they just touch the jacket without squashing it, twice at right angles because many cables are oval or flat. Measure the plug as well if the cable has to pass through the clip, and the screw or the desk edge the clip fixes to.