Own a 3D printer but not the CAD skills? Parts you can make tonight

How to design dice towers, card holders and miniature bases for 3D printing in 2026

Design your own dice tower, dice tray, card holder, deck box, token trays, box insert and plain bases: what to measure for each, and the prompt that makes it.
17 November 2026 · 7 min readtabletopboard gamesorganizer

The accessories around a game are boxes, trays, ramps and discs with real dimensions, which makes them some of the easiest parts to design yourself: measure your dice, your sleeved cards and the inside of the game box, then describe the part or shape it by hand. The miniatures are a different job. A sculpted figure comes from a sculpting program or a model site, not from a CAD for functional parts, and SpeakCAD does not make them.

The short answer

  • Dice tower: every opening at least 30 mm wide, ramps at 45°.
  • Dice tray: walls 20 to 25 mm tall, a flat floor for felt.
  • Card holder: a slot sized from a stack of ten cards.
  • Deck box: the sleeved card plus 1 mm per side.
  • Token tray: one compartment per kind of token.
  • Box insert: the inside of the box minus 2 mm, as lift-out trays.
  • Bases: plain discs and squares about 3 mm thick.
  • Miniatures, monsters, carved terrain: not here. Sculpt them or download them.

What to measure

AccessoryMeasureThe number that decides it
Dice towerYour biggest die, corner to cornerOpenings at least 30 mm, and 10 mm more than that die
Dice trayThe space on the table, your print bedWalls 20 to 25 mm tall
Card holderTen cards stacked, one card's widthThe slot's width; about 10 mm deep
Deck boxA sleeved card, the deck squeezed lightlyInside: the card plus 1 mm per side
Token trayThe biggest token of each kindA compartment 5 mm wider than it
Box insertThe box inside, the board and rules on topOutside: the box inside minus 2 mm
BasesA base you own, the magnetIts diameter; a 6.2 mm pocket for a 6 mm magnet

A calliper makes all of this quicker, and how to measure an object for a printed part says which sizes need one.

Dice tower

A dice tower is a hollow column: dice go in at the top, tumble down a few ramps that lean alternately left and right, and roll out into a tray. What makes one work is room. A standard six-sided die is 16 mm, but other dice are larger, and a die has to pass every gap corner first. Measure your biggest across its points, and keep every opening at least 30 mm wide and 10 mm wider than that.

Three ramps are enough in a tower 150 to 180 mm tall. Set them at 45°: steep enough that dice keep moving, and the steepest overhang that prints cleanly without supports, so the tower prints upright in one piece. Walls of 2 mm, and a tray with a lip so the dice stop.

Prompt
A dice tower 70 x 70 mm and 160 mm tall with 2 mm walls, a 40 mm square opening on top, three internal ramps at 45 degrees on alternating sides, and a 40 mm wide exit at the bottom into an attached tray 120 x 80 mm with 15 mm walls.

Square battlements on top are fine: they are notches. Carved stonework, skulls and dragons are sculpting. The library has a plain tower with a catch tray to start from.

Dice tray

A shallow open tray, as big as your table space and your print bed allow, with walls 20 to 25 mm tall so a thrown die stays in. Leave the floor flat and glue in a sheet of felt: dice on bare plastic are loud, and they bounce. This one needs no AI. Start from the Tray starter and type its sizes and its corner radius.

Card holder

A holder for a hand of cards is a strip with a long slot the cards stand in, for children and for anyone who finds a fan of cards hard to hold. Cards overlap in the slot, so it has to be as wide as three or four cards are thick: stack ten of your cards, measure the stack, and work it out. A slot about 10 mm deep that leans back 15 to 20° shows every card to its owner and nobody else. A poker-size card is 63.5 mm wide, so a strip 200 mm long holds a hand of seven, overlapped.

By hand you get an upright slot: the Plate starter made 20 mm thick, then Cut a slot in its top face. A slot that leans back, or a holder that curves, is a sentence to the AI.

Deck box

A poker-size card is 63.5 × 88 mm, but nobody stores bare cards: sleeves add to both sizes, and how much depends on the sleeves. Measure one sleeved card, and the whole deck squeezed lightly between two fingers. The inside of the box is the card plus 1 mm per side, so the deck drops in and lifts out, and the stack plus 2 mm. Walls of 1.6 mm, and a thumb notch 20 mm wide on each side to pull the deck out.

For the lid, a cap that slides over the top with 0.3 mm of clearance is the simplest, and a sliding lid the safest in a bag; snap-fit vs screws vs magnets goes through each closure. By hand: the Open box starter with its width, length, height and wall typed, then Text for the deck's name on the front, in letters 5 mm tall or more.

Token trays and box inserts

A token tray is a small drawer organiser, and the rules of a drawer insert apply: lay the tokens out by kind, measure the biggest of each, add 5 mm for fingers, and give every kind its own compartment. Walls of 1.2 mm are plenty, 20 to 25 mm tall. A curved floor that lets a fingertip slide a token out is worth asking for: "a scoop along the front wall of each compartment".

A box insert starts from the box, not the pieces. Measure the inside width and depth, then the height, and take away the thickness of the board and the rulebook that lie on top: what is left is the height of the insert. Subtract 2 mm from the width and the depth so it drops in. Then split it into separate trays, one per player or per kind of piece, each smaller than your print bed. Trays that lift out and go on the table set a game up faster than one fixed block. If the box is stored on its edge, let the trays reach to within a millimetre or two of the lid, so nothing wanders.

Prompt
A tray 140 x 95 x 30 mm outside for a board game box, 1.2 mm walls and floor, four compartments 60 x 40 mm for tokens with a scoop along the front wall of each, and one well 66 x 90 mm for a deck of cards with a 20 mm finger notch at each end.

Bases

A plain base is a disc or a square about 3 mm thick. Round bases of 25, 32 and 40 mm are common, and a 25 mm base suits a map with a 1 inch grid, but games differ: check the rules, or measure a base you own. Two options are worth adding. A slot through the middle takes a figure with a tab under its feet (measure the tab). A pocket underneath takes a magnet, 6.2 mm across and 2.2 mm deep for a 6 × 2 mm one, so the figures hold in a steel-lined case.

By hand: the Cylinder starter at 32 mm across and 3 mm tall, then Cut a circle in the underside for the magnet. Print bases flat, at 0.12 to 0.16 mm layers for a clean top. A movement tray for a unit is a plate with one shallow recess per base, 1 mm wider than the base.

What SpeakCAD does not do here

SpeakCAD is a CAD for functional parts with real dimensions. It does not make figurines, faces, creatures, sculpted rock or textures, so the miniatures, the monsters and the carved terrain come from elsewhere: a sculpting program such as Blender or Nomad, an AI mesh generator (how they differ), or a model site (where to download STL files). What it does is the part nobody published: the insert for your box, the tray for your tokens, the deck box for your sleeves.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

Prompts to start from

Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.

A dice tower 70 x 70 mm and 160 mm tall with 2 mm walls, a 40 mm square opening on top, three internal ramps at 45 degrees on alternating sides, and a 40 mm wide exit at the bottom into an attached tray 120 x 80 mm with 15 mm walls

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A deck box for 100 sleeved cards with an inside of 69 x 94 x 68 mm, 1.6 mm walls, 3 mm rounded corners, a 20 mm thumb notch on each side and a cap lid 25 mm tall that slides over the top with 0.3 mm clearance

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A round miniature base 32 mm across and 3 mm thick with a 1 mm bevel on the top edge, a through slot 20 mm long and 1.5 mm wide in the centre, and a pocket 6.2 mm across and 2.2 mm deep underneath for a 6 x 2 mm magnet

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

Questions

No. SpeakCAD is a CAD for functional parts with real dimensions and does not make figurines, creatures, faces or sculpted textures. Miniatures come from a sculpting program, an AI mesh generator or a model site. What it designs is everything around them: dice towers and trays, card holders, deck boxes, token trays, box inserts, plain bases and movement trays.

About 150 to 180 mm tall with three internal ramps and 2 mm walls, and every opening at least 30 mm wide and 10 mm wider than your biggest die measured corner to corner. Ramps at 45° keep the dice moving and let the tower print upright without supports.

Measure your own sleeved cards, because sleeves differ: a bare poker-size card is 63.5 × 88 mm and sleeves add to both sizes. Make the inside 1 mm larger than the sleeved card on each side, and as deep as the deck squeezed lightly plus 2 mm, with 1.6 mm walls.

Round bases of 25, 32 and 40 mm are common, about 3 mm thick, and a 25 mm base suits a map with a 1 inch grid. Games differ, so check the rules or measure a base you own. A 6 × 2 mm magnet underneath needs a pocket 6.2 mm across and 2.2 mm deep.

Measure the inside of the box, then take the thickness of the board and the rulebook off the height and 2 mm off the width and the depth. Split the insert into separate lift-out trays smaller than your print bed, with 1.2 mm walls, one compartment per kind of piece and a finger notch at each end of a card well.

Make your first part tonight

No CAD, no tutorial. Type what you need on your phone or laptop, watch it render, and send the STL to your slicer. Try the live demo first, no account; your own part starts with Maker at $7.99 a month, cancel anytime.