Fit-test coupon

A free fit-test coupon for your Bambu Lab printer

A printed hole comes out smaller than it was drawn, and by how much depends on your printer. This small gauge has three openings 0.2 mm apart. Print it in a few minutes, try the real screw, bearing or profile in it, and you know which size to use before you print the part that needs it.
Which fit do you need to test?
One e-mail with the STL attached. No account, no card.

Bambu Lab printers

SpeakCAD slices for 12 Bambu Lab printers, the A1, the A1 mini and the H2D among them. The coupon is the same file for all of them: what differs from one machine to the next is which opening fits, and that is what it is for. Print it with the filament and the profile you will use for the real part.Bambu Lab printers in the slicer

From the e-mail to the right size

  1. Pick the fit you need. An M3 screw hole, a pocket for a 608 bearing, or a slot over a 2020 extrusion. Type your e-mail address and the STL arrives in your inbox.
  2. Print the coupon. Flat on the bed as it arrives, 0.2 mm layers, no supports, in the filament of the final part. It is a few minutes and about a gram or two of filament.
  3. Try the real object in each opening. The screw, the bearing or the profile you actually own, in the opening with one dot, then two, then three.
  4. Read the result. Too tight: the object does not go in, or only with force. Right: it goes in the way the part needs, pressed or free. Too loose: it rattles or falls out. Keep the size of the opening that was right.
  5. Use that size in your part. Type it as the diameter or the width in your design. In SpeakCAD the coupon opens as a model whose three sizes are numbers you can retype to test other values.

What each opening tells you

One dot is the tightest opening, three dots the widest. Each is described as it behaves on a well-tuned printer; if yours lands one opening over, that is the number you were missing.

M3 screw

36 × 12 × 4 mm, about 3 minutes and 1.2 g of filament (estimated). Push an M3 screw through each hole, from the side with the dots.
One dot · 3.2 mm
the screw bites into the plastic
Two dots · 3.4 mm
the screw passes with a snug fit
Three dots · 3.6 mm
the screw drops through freely

608 bearing

77.2 × 26.4 × 4 mm, about 3 minutes and 1.4 g of filament (estimated). Press a 608 bearing into each ring by hand, on a flat table.
One dot · 22 mm
a hard press, or no entry at all
Two dots · 22.2 mm
a firm press by hand
Three dots · 22.4 mm
the bearing slides in and can fall out

2020 extrusion

76.6 × 13 × 4 mm, about 4 minutes and 1.5 g of filament (estimated). Set each slot over the side of the extrusion and push it down.
One dot · 20 mm
a tight clamp, or no entry at all
Two dots · 20.2 mm
a snug fit that stays put
Three dots · 20.4 mm
a loose fit that slides along the profile

By printer brand

The same coupons, with the printers of each brand that SpeakCAD slices for.

Questions

Which of three sizes fits the real object on your printer. Each coupon has three openings 0.2 mm apart (0.1 mm per side), marked with one, two and three dots: 3.2, 3.4 and 3.6 mm for an M3 screw; 22, 22.2 and 22.4 mm for a 608 bearing (22 mm outside, 7 mm wide); 20, 20.2 and 20.4 mm for a 2020 aluminium extrusion (20 mm across). The opening that fits the way you want is the number to use in your part.

Flat on the bed as it arrives, at 0.2 mm layers, without supports, with the same filament and print profile as the part you are going to make. A fit changes with the material and the profile, so a coupon printed in another filament tells you about that filament.

Yes. The STL is e-mailed to you and needs no account and no card. Your address is used to send that one e-mail. If you tick the box, we also send a few tips on designing parts that fit, and every e-mail has an unsubscribe link.

The coupon is a fixed gauge for three common fits. Fit Check works on your own part: SpeakCAD is the only AI 3D editor that calibrates itself to your printer: Fit Check cuts a five-minute test slice from the part that must fit, you report too tight, perfect or too loose, and every model after that is built with the clearance your printer needs.

Yes: it is a plain STL, so any slicer and any printer take it. SpeakCAD also slices G-code for 380+ printers if you would rather not install a slicer.

Your next print is a few taps or one sentence away

Shape a part with the free hand tools on your phone or computer, or describe it and let the AI build it, then download an STL, or G-code sliced for your printer. A free account brings the hand tools and their files, plus your first AI part on us (some accounts confirm it with a card first, nothing charged that day); then the AI runs on credits, from Maker at $7.99 a month for 50 credits, or Pro from $14.99 a month, cancel anytime. Nothing to install. Not sure yet? Shape a real part in the live demo first, no account needed.