Which 3D printer to buy, and what to make with it

Direct drive vs Bowden in 2026: what the extruder changes for the parts you print

Direct drive or Bowden in 2026: what the extruder changes for TPU, stringing and toolhead weight, which printers use which, and how to design parts for each.
17 November 2026 · 7 min readextruderexplainerprinters

A direct-drive extruder rides on the toolhead and pushes the filament a few centimetres into the nozzle. A Bowden extruder sits on the frame and pushes it through a long tube. For the parts you print, the difference shows in three places: flexible filament, strings between separate features, and the weight the head carries. In 2026 the question is mostly settled. Of the 24 printers featured on this site, 21 are direct drive and 2 are Bowden: the Prusa MINI and Creality Ender-3.

The extruder of each printer, and the wording in the table further down, come from the makers' pages, checked on 29 September 2026. SpeakCAD sells no printer and has profiles for both kinds.

The short answer

  • Buying a printer now: direct drive. You get it almost by default, and it is the kind that prints TPU without a fight.
  • You own a Bowden printer and print PLA and PETG: keep it. It prints both well; expect a few more strings.
  • You want flexible parts (feet, gaskets, bumpers): direct drive. A Bowden printer manages firm TPU slowly and struggles with softer grades.
  • You own an original Ender-3 and like upgrades: a direct-drive conversion is one of the common ones.
  • Do not choose a printer on this alone. Bed size, an enclosure and the price change more.

Side by side

Direct driveBowden
Where the motor sitsOn the toolhead, just above the hotendOn the frame, at the far end of a tube
Filament between the gears and the nozzleA few centimetresThe length of the tube
TPU and other flexible filamentA normal filament, printed slowly95A slowly; softer grades are a struggle
RetractionShort: about a millimetreLong: several millimetres
Strings between separate featuresFewerMore, most of all in PETG
Weight on the toolheadMoreLess
Printers featured here212

What each one is

Every extruder has a motor and a pair of gears that grip the filament and push it into the hotend, where it melts. In a direct drive those gears ride on the toolhead, directly above the hotend. In a Bowden setup the motor and the gears are bolted to the frame, and the filament travels to the hotend inside a PTFE tube, the way a brake cable runs inside its housing.

Flexible filament: the difference you can feel

TPU bends, which is the point of it and the trouble with it. Pushed from the frame through a long tube, it compresses and buckles before the pressure reaches the nozzle, so the printer has to go slowly and soft grades jam. Pushed from a few centimetres away, it has nowhere to buckle. That is why a direct drive treats the common 95A hardness as an ordinary, slow filament, while a Bowden printer manages 95A with patience and little that is softer.

For the part, this decides what you can design. With direct drive, feet, gaskets, bumpers and grips are ordinary parts: walls and infill set how soft they feel (few walls and 10 to 15% infill for a soft bumper, more of both for a firm one), and they print best with a flat face down and no supports. On a Bowden printer it is often easier to put the flex in the shape and keep the material rigid: a PETG clip arm at least six times as long as it is thick bends without cracking. Which filament for which part covers the rest of the shelf.

One trap on multi-colour machines: most soft TPU is fed from the external spool holder and not through the automatic filament unit, so check what yours accepts.

Retraction and strings

Each time the nozzle crosses a gap, the printer pulls the filament back a little so that nothing oozes on the way. That is retraction. A direct drive pulls back about a millimetre and the nozzle answers at once. A Bowden setup has slack between the filament and its tube, so it has to pull back several millimetres, and the answer is slower and less exact. The result is thin strings between separate features and small blobs where a line starts, most of all in PETG, which strings more than PLA on any printer.

You do not type these numbers. The printer's profile and the filament preset carry the retraction for that machine, and SpeakCAD uses the OrcaSlicer profile of the printer you pick, the Bowden ones included. If strings persist with the right profile, suspect a damp spool before the extruder.

What you can do in the design, on a Bowden printer above all:

  • Fewer islands. Two posts joined by a low wall print as one outline, with no travel between them.
  • Fewer copies per plate. Every hop from one part to the next is a retraction, and a row of small pins is the worst case.
  • No tall, thin, separate features. Tie a standoff or a pin to the nearest wall with a small rib: it strings less and it is stronger.

Weight on the toolhead

The case for Bowden was always weight. With the motor on the frame the head is lighter, and a lighter head rings less when it changes direction. Two things removed most of that advantage. Extruders became small and light enough to ride on the head, and input shaping, which cancels the ringing in firmware, is now on both kinds: the Prusa MINI itself received it in a firmware update. On a bed slinger the heavy moving part is the bed and the print on it, whatever the extruder, as bed slinger vs CoreXY explains. Weight is no longer a reason to pick Bowden, and it is nothing you design around.

PrinterKindExtruder, from the maker's description
Bambu Lab A1Direct driveDirect drive; quick-swap hotend (nozzle and hotend change as one unit), 300 °C
Prusa MK4SDirect driveNextruder planetary direct drive, load-cell bed levelling, 360° part cooling
Prusa MINIBowdenBowden (TPU is harder), all-metal hotend; input shaping arrived by firmware update
Creality Ender-3 V3 SEDirect driveSprite direct drive; CR Touch levelling with a strain-gauge Z offset; no input shaping
Creality Ender-3BowdenBowden; manual bed levelling (the V2 Neo adds CR Touch)
Creality K1CDirect driveDirect drive to 300 °C; hardened quick-swap nozzle, clog-resistant extruder
Elegoo Neptune 4 ProDirect driveDual-gear direct drive; 121-point auto levelling
Voron 2.4Builder's choiceYour choice of toolhead and hotend

Every other featured printer is direct drive. The Bowden machines are older designs: the Prusa MINI dates from 2019 and the original Ender-3 is discontinued in most stores. A1 mini vs Prusa MINI compares one extruder of each kind on the same 180 x 180 x 180 mm volume.

Which to choose

Direct drive is the default, and what it gives up is small: a little more mass on the head, which firmware now compensates. Look elsewhere if you already own a Bowden printer that prints your PLA and PETG parts well: direct drive alone is not a reason to replace it.

Bowden still makes a quiet, simple machine for rigid filaments. Look elsewhere if flexible parts are on your list, or your parts are full of small separate features in PETG.

If you keep a Bowden printer, keep the spools dry, buy 95A when you need TPU and feed it slowly, and put the flex in the shape where you can. On an Ender-3, a direct-drive conversion is a well-trodden upgrade, and several of the parts around it are ones you print yourself: printer upgrades you can print.

Sources

Extruders of the featured printers: the makers' pages, checked on 29 September 2026 (bambulab.com, prusa3d.com, creality.com, elegoo.com and vorondesign.com). TPU, PETG and what the filament preset decides: print settings by material. Snap arms: tolerances and clearances.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

Prompts to start from

Open one in the builder, change the numbers to yours, and the model renders in your browser, usually within a minute or two. Keep adjusting in the chat before you print.

Four round feet in TPU, 30 mm in diameter and 8 mm tall, each with a 15 mm recess 2 mm deep on top for a cabinet leg and a flat bottom.

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A flat gasket in TPU for a 90 x 60 mm enclosure lid: 2 mm thick, 5 mm wide all round, with four 3.4 mm holes on an 80 x 50 mm pattern.

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

A cable clip in PETG with a flexible arm 18 mm long and 2 mm thick that snaps over a 6 mm cable, fixed with one 3.5 mm countersunk screw.

Open in the builderPre-filled after sign-in. Try it in the live demo first, no account needed.

Questions

For most people in 2026, yes. A direct-drive extruder pushes the filament from a few centimetres above the nozzle, so it prints flexible TPU normally and retracts cleanly, with fewer strings. A Bowden extruder pushes through a long tube: it prints PLA and PETG well, strings a little more, and struggles with soft filament. Its old advantage, a lighter toolhead, matters much less now that input shaping is common.

Firm TPU, slowly. The common 95A hardness can be printed on a Bowden printer with patience, because the filament compresses and buckles in the long tube; softer grades are a struggle and often jam. For flexible parts printed regularly, a direct-drive printer is the easier tool.

Because of the slack between the filament and its tube. To stop the nozzle oozing during a travel move, a Bowden setup has to pull the filament back several millimetres where a direct drive pulls back about one, and the response is slower and less exact. The printer's profile carries the right retraction, so check for a damp spool before blaming the extruder.

Almost all current ones. Of the 24 printers featured on SpeakCAD, 21 are direct drive, including the Bambu Lab A1 and P1S, the Prusa MK4S and CORE One and the Creality Ender-3 V3 SE and K1C. The Bowden ones are the Prusa MINI and Creality Ender-3, and a Voron takes whichever toolhead its builder chooses.

Only if you want flexible parts or cleaner PETG. For PLA and most PETG parts a well-set-up Bowden Ender-3 prints fine, and dry filament and the right profile fix most stringing. If TPU is on your list, a direct-drive conversion is one of the common upgrades for that printer.

Whichever printer you pick, the first custom part is a sentence away

Describe a part with its measurements, check it on a virtual bed the size of your printer's, and download G-code sliced with its official profile, or the STL for your own slicer. Try the live demo first, no account; your own parts start with Maker at $7.99 a month, cancel anytime.