---
title: "What to design first for your 3D printer: how to pick the part, and seven that work"
description: "Your first CAD part should be small, flat and fit one thing you own. Five rules for picking it, seven parts that pass, and what to leave for later."
canonical: https://speakcad.com/blog/what-to-design-first-for-your-3d-printer
published: 2026-11-17
updated: 2026-11-17
publisher: SpeakCAD
---

# What to design first for your 3D printer: how to pick the part, and seven that work

> Your first CAD part should be small, flat and fit one thing you own. Five rules for picking it, seven parts that pass, and what to leave for later.

The first part you design decides whether there is a second one. Pick a snap-lid enclosure with a hinge and you spend a weekend on three fits at once. Pick a cube and you learn nothing, because a cube does not have to fit anything. A good first part is small, lies flat on the bed, and has to fit exactly one thing you own.

## Five rules for picking it

1. **You need it this week.** A part with a job gets printed, tried and fixed. A part made for practice gets abandoned at the first miss.
2. **One fit, one measurement that decides.** A screw that must pass through, a tube a cap must grip, a drawer a tray must drop into. One number to get right, so when the print is off you know which number to change.
3. **It lies flat on the bed.** A flat face down and no overhang past 45° means no supports and nothing to tune in the slicer. You are testing your design, not your print settings.
4. **Small enough to print twice.** The size of your palm, a few millimetres thick. Expect two or three rounds, and keep each one short.
5. **Nothing that moves.** No hinge, no thread, no snap lid. Each adds a fit that depends on your printer, and you do not know your printer's numbers yet.

## Seven first parts that pass

Each has sizes you can replace with your own, the measurement that decides it, and the idea it teaches. The first five are a few taps with the hand tools; the last two are quicker to describe.

| Part | Sizes to start from | The measurement that decides | What it teaches |
|---|---|---|---|
| A spacer | 20 mm across, 10 mm tall, a 5.5 mm hole through the middle | The bolt: M5 | A hole is bigger than its screw |
| A plate with four holes | 100 × 60 × 3 mm, an M4 hole 6 mm from each corner | The hole spacing on the thing it bolts to | Positions are measured from edges |
| An open box | 60 × 40 × 25 mm outside, 2 mm walls, rounded corners | The biggest thing that goes in it | Inside and outside are different numbers |
| A drawer tray | The drawer's inside width and depth, less 2 mm each | The drawer, measured with a ruler | When a ruler is enough |
| A cap for a tube | A 25.8 mm hole, 15 mm deep, for a 25.4 mm tube | The tube's outside diameter | Clearance: 0.2 mm per side for a cap that stays on |
| A wall hook | 15 mm wide, sticking out 40 mm, two countersunk holes for 4 mm screws 30 mm apart | The screws, and what hangs on it | Which way up a part prints |
| A cable clip | For a 6 mm cable, fixed with one 3.5 mm wood screw | The cable's diameter | Describing a part by what it holds |

**The spacer** is about as small as a useful part gets. Start from the Cylinder shape, type 20 and 10, tap the top, pick Hole and the M5 preset, and it is done. The preset is 5.5 mm, not 5, because a printed hole comes out 0.2 to 0.4 mm smaller than drawn. Print it, push the bolt through, and you have tested how your printer prints holes.

**The plate** is the first part many people actually need: something that bolts to something else. Start from the Plate shape, then place one hole by its distance from two edges. Measured on the editor, an M4 hole 6 mm from two edges of a plate is 4 taps and 2 typed numbers. Duplicate copies it to the other three corners. Before printing, tap Measure and two holes, and compare the spacing with the thing the plate bolts to.

**The open box and the drawer tray** both start from the Open box shape, whose width, length and height are outside sizes. They teach the sum every case and holder repeats: the inside is the outside less two walls. [Inside or outside?](/blog/inside-or-outside-dimensions-3d-printed-box) works through it.

**The cap** is the first part with a real fit. Measure the tube with callipers at three places ([how to use them](/blog/how-to-use-digital-calipers-for-3d-printing)) and add 0.2 mm per side. By hand it is a cylinder 29 mm across and 17 mm tall with a 25.8 mm hole, 15 mm deep, centred on the top. If it is loose or will not go on, you change one number, which is the point of rule 2.

**The hook and the clip** have curves and a bend that carries weight, so describe them to the AI with their sizes instead of building them from boxes. One thing to know before slicing: print a hook lying on its side, so the layers run along the hook, not across it.

## What to leave for the fourth part

- **Snap-fit lids and clips that must click.** The click depends on a few tenths of a millimetre, and they differ from one printer to the next.
- **Hinges and anything printed in place.** Two fits that must both be loose, in one print.
- **Threads.** Printed threads work from about M8 up. Until then, use a plain hole and a real screw.
- **A two-part enclosure for a board.** Board, standoffs, ports and lid: four fits at once.

Each of these is tuned to your printer, and you learn your printer one fit at a time. When you get there, [Fit Check](/guides/fit-check-parts-that-fit-first-time) cuts a five-minute test slice around the fit and keeps the clearance your printer needs for the parts that follow.

## By hand or by description

SpeakCAD is CAD for 3D printing with two ways in. The hand tools (Hole, Cut, Add, Extrude, Text, Round, Fillet, Shell and Measure) work by tapping a face and typing millimetres, starting from an Open box, a Plate, a Cylinder or a Tray that already has its sizes. They are free, and so is the STL or 3MF of what you shaped by hand. Or you describe the part in plain words: the AI writes a parametric program for it, your browser compiles it, and that route spends credits.

Start by hand when the part is a box, a plate or a cylinder with holes in it, and describe it when it has a curve or a clip. The [live demo](/demo) is the real editor with a ready part: the hand tools work there with no account, and so do 3 AI edits.

## When it comes off the bed

1. **Measure it.** Callipers across the outside, against the number you typed. A tenth or two over is normal: outside walls print slightly fat.
2. **Test the fit.** The bolt through the hole, the cap on the tube. Too tight or too loose, and by how much? Write the number down.
3. **Look at the bottom edge.** The first layer is squashed onto the bed and flares out by 0.1 to 0.3 mm. If the part must slide into something, a 0.5 mm chamfer on the bottom edge takes care of it.

Then change one number and print again. That loop, more than any drawing skill, is what makes parts fit.

## The second part

[CAD for beginners](/cad-for-beginners) puts five parts in order, each adding one idea to the last, and names the six ideas every CAD program shares. Before the second part, try [sketching it on paper first](/blog/sketch-a-part-on-paper-before-cad): it takes five minutes and a pencil.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

## Prompts to try

- A spacer 20 mm across and 10 mm tall with a 5.5 mm hole through the middle ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520spacer%252020%2520mm%2520across%2520and%252010%2520mm%2520tall%2520with%2520a%25205.5%2520mm%2520hole%2520through%2520the%2520middle))
- A cap for a tube 25.4 mm outside diameter, 15 mm deep, 0.2 mm clearance per side, 1.6 mm wall, closed end 2 mm thick ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520cap%2520for%2520a%2520tube%252025.4%2520mm%2520outside%2520diameter%252C%252015%2520mm%2520deep%252C%25200.2%2520mm%2520clearance%2520per%2520side%252C%25201.6%2520mm%2520wall%252C%2520closed%2520end%25202%2520mm%2520thick))
- A wall hook 15 mm wide that sticks out 40 mm, with two countersunk holes for 4 mm screws, 30 mm apart ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520wall%2520hook%252015%2520mm%2520wide%2520that%2520sticks%2520out%252040%2520mm%252C%2520with%2520two%2520countersunk%2520holes%2520for%25204%2520mm%2520screws%252C%252030%2520mm%2520apart))

## FAQ

### What should I design first for my 3D printer?

A small flat part that fits one thing you own and that you need this week: a spacer, a plate with screw holes, an open box, a cap for a tube. One fit means one number to correct when the first print is off. Leave snap lids, hinges and threads for later parts, because each adds a fit that depends on your printer.

### Is a calibration cube a good first design?

It is a good first print and a poor first design. A cube shows how your printer prints a 20 mm wall, but it does not have to fit anything, so it teaches nothing about holes, clearance or measuring. A spacer with a hole for a real bolt is as quick to make and tests a fit.

### Can I design a first part without learning CAD?

Yes. In SpeakCAD you start from an open box, a plate, a cylinder or a tray that already has its sizes, tap a face and type the millimetres for a hole or a cut; the hand tools and the STL or 3MF they make are free. Or describe the part in a sentence with its sizes and the AI builds it, which spends credits.

## About SpeakCAD

SpeakCAD is the most intuitive CAD for 3D printing, made for people who own a 3D printer and need a part that fits something they have: tap a face and type a size to shape it with simple tools, or describe it to the AI, on your phone or computer, and download a print-ready STL, 3MF or G-code sliced for your printer.

SpeakCAD works inside ChatGPT and Claude as a plugin (an MCP server): ask the assistant for a part with its measurements and SpeakCAD's own CAD AI designs it, shows it in 3D in the chat and hands over a print-ready STL, 3MF or G-code sliced for your printer.

- Live demo, no account: https://speakcad.com/demo
- In ChatGPT, Claude and other MCP clients: https://speakcad.com/chatgpt-plugin, https://speakcad.com/claude-connector, https://speakcad.com/mcp-server
- Pricing: https://speakcad.com/pricing
- FAQ: https://speakcad.com/faq
- Site index for AI assistants: https://speakcad.com/llms.txt
