---
title: "Boss, rib, lip, flange, lug: the names for the bits of a part, so you can ask for them"
description: "You can picture the part but not name its pieces. Two dozen names for the features of a printed part, what each is for, and the size that makes it print."
canonical: https://speakcad.com/blog/names-of-part-features-boss-rib-lip-flange
published: 2026-11-17
updated: 2026-11-17
publisher: SpeakCAD
---

# Boss, rib, lip, flange, lug: the names for the bits of a part, so you can ask for them

> You can picture the part but not name its pieces. Two dozen names for the features of a printed part, what each is for, and the size that makes it print.

You know exactly what the part should look like, and the sentence still comes out as "a sort of raised round bit with a hole, next to the flat part that sticks out". The pieces of a part have names. Knowing two dozen of them makes a description shorter, a search more useful and an AI's first answer much closer. Each name below comes with what the feature is for and, where there is one, the number that makes it print.

## Things that stand up

- **Boss.** A raised cylinder on a surface, usually there to take a screw. A 6 mm boss suits an M3 screw.
- **Standoff.** A boss whose job is to hold something off the floor, such as a circuit board above the bottom of a case: 6 mm across and 4 mm tall, say, with a 2.5 mm hole for an M3 screw that cuts its own thread.
- **Peg (or pin).** A solid cylinder that locates one part on another, with no screw. A 5 mm peg goes into a 5.3 mm hole.
- **Tab.** A small flat tongue sticking out of an edge or a face: something to screw through, to hook under, or to stop a lid sliding.
- **Lug (or ear).** A tab with a hole in it, for a screw, a cable tie or a key ring. For a key ring, a lug 3 mm thick with a 5 mm hole.
- **Rib.** A thin wall added to stiffen: under a shelf, across the floor of a wide tray. Make it as thick as the part's walls, and no thinner than 1.2 mm.
- **Gusset.** A triangular rib in an inside corner, between the two legs of a bracket.

## Things that are cut in

- **Hole.** Round, and either **through** (out the other side) or **blind** (stopping at a depth). A hole that a screw passes through is a **clearance hole**: 3.4 mm for M3, 4.5 mm for M4.
- **Counterbore and countersink.** The wider step, or the cone, at the top of a hole that lets a screw head sit flush.
- **Pocket (or recess).** A flat-bottomed cut that does not go through: a seat for a magnet, a nut or a rubber foot. A 6 mm magnet presses into a 6.2 mm pocket.
- **Nut trap.** A six-sided pocket that holds a nut so that it cannot turn while you tighten the screw.
- **Slot.** A hole stretched into a line, with round ends: for a screw that needs adjusting, a cable or a strap.
- **Notch.** A cut in an edge, open on one side: where a cable leaves a case.
- **Window (or cutout).** An opening through a wall for a connector, a switch or a display. Give it 0.5 mm of room all round what shows through it.
- **Groove (or channel).** A long, shallow cut along a surface: for a wire, a seal or a sliding lid.

## Edges and rims

- **Lip.** A small raised edge. At the front of a phone stand it stops the phone sliding off; round the inside of a lid it locates the lid on its box, 0.3 mm smaller than the opening on every side.
- **Rim.** The top edge of a wall, all the way round an opening.
- **Flange.** A flat rim that sticks out sideways from the body, usually with holes in it, so that the part can be screwed down flat.
- **Shoulder (or step).** A change in diameter or height that something rests against: where a peg gets wider so that it stops at the right depth.
- **Fillet and chamfer.** A rounded edge and an angled one. A fillet of 2 to 3 mm inside a bend makes a bracket stronger; a 0.5 mm chamfer on the bottom edge hides the flare of the first layer.
- **Lead-in.** A chamfer whose job is to guide: on the mouth of a hole so that a peg finds it, on a clip so that it snaps past.

## Things that hold

- **Clip (or snap fit).** A springy arm with a hook on the end, which bends, passes an edge and springs back. The arm should be at least six times as long as it is thick, and printed lying flat so that it bends along the layers.
- **Clamp.** A ring with a gap and a screw across the gap, to grip a tube.
- **Hinge.** Two parts joined by a pin they turn on. The pin wants a loose fit: 0.8 mm of clearance or more.
- **D-flat.** The flat on one side of a shaft or a bore, so that a knob turns the shaft and does not spin on it.
- **Thread.** The spiral on a screw, or in a hole. Printed threads work from about M8 up; below that, use a real screw in a plain hole.

## Which ones you can make by hand

In SpeakCAD, a good part of this list is a tap on a face and a number, with the hand tools.

| Feature | Tool |
|---|---|
| Hole, clearance hole, counterbore, countersink | Hole, with its screw presets and Screw head |
| Pocket, slot, notch, window, nut trap | Cut: a rectangle, a circle, a slot or a hexagon, through or to a depth |
| Boss, standoff, peg, tab, lug, rib | Add: a shape of the size you type, standing on the face you tapped |
| Walls and a floor out of a solid block | Shell |
| A fillet, a chamfer or a lead-in on a straight edge | Fillet and Round |
| A row, a grid or a circle of holes, cuts or added shapes | Duplicate |

Shaping a part with these is free, and so is the STL or 3MF of what you shaped by hand. A clip, a hinge, a thread, a gusset or anything on a curved surface is quicker to describe: the AI writes the part as a parametric program and your browser compiles it, and that spends credits. [The hand tools page](/tools) says what each tool does, and [the guide](/guides/hand-tools) shows them on one part.

## Putting the words into a sentence

Compare two ways of asking for one part:

> A box with round raised bits inside for the board screws and a flat part sticking out at each end with holes to screw it to the wall.

> A box 75 × 55 × 20 mm outside with 2 mm walls, four standoffs 5 mm tall for M3 self-tapping screws on 62 × 42 mm centres, and a flange 15 mm wide at each short end with one 4.5 mm hole.

The second is hardly longer, and every noun in it is a feature with a size. An order that works: the body first, then what stands up, then what is cut in, then the edges. [How to describe a part](/guides/prompting-for-cad) covers the rest of a good description.

If you can draw it but not name it, draw it: [a five-minute sketch](/blog/sketch-a-part-on-paper-before-cad) with the numbers on it reads out as a description, line by line. The sums behind "75 × 55 mm outside" are in [inside or outside?](/blog/inside-or-outside-dimensions-3d-printed-box), and the symbols on a maker's drawing (Ø, R, 4×) are in [how to read a dimension drawing](/blog/how-to-read-a-dimension-drawing-for-3d-printing).

The words for what you do to a part (extrude, boolean, shell, pattern) are in the [CAD glossary](/blog/cad-terms-explained-for-3d-printing). And [CAD for beginners](/cad-for-beginners) puts five first parts in order; the names above are what those parts are made of.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

## Prompts to try

- A box 75 x 55 x 20 mm outside with 2 mm walls, four standoffs 5 mm tall for M3 self-tapping screws on 62 x 42 mm centres, and a flange 15 mm wide at each short end with one 4.5 mm hole ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520box%252075%2520x%252055%2520x%252020%2520mm%2520outside%2520with%25202%2520mm%2520walls%252C%2520four%2520standoffs%25205%2520mm%2520tall%2520for%2520M3%2520self-tapping%2520screws%2520on%252062%2520x%252042%2520mm%2520centres%252C%2520and%2520a%2520flange%252015%2520mm%2520wide%2520at%2520each%2520short%2520end%2520with%2520one%25204.5%2520mm%2520hole))
- A plate 60 x 40 x 4 mm with a lug 12 mm wide at one end with a 5 mm hole, and a pocket 6.2 mm across and 2.2 mm deep in the middle for a 6 x 2 mm magnet ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520plate%252060%2520x%252040%2520x%25204%2520mm%2520with%2520a%2520lug%252012%2520mm%2520wide%2520at%2520one%2520end%2520with%2520a%25205%2520mm%2520hole%252C%2520and%2520a%2520pocket%25206.2%2520mm%2520across%2520and%25202.2%2520mm%2520deep%2520in%2520the%2520middle%2520for%2520a%25206%2520x%25202%2520mm%2520magnet))
- An L bracket 60 x 60 mm, 30 mm wide, 4 mm thick, with a gusset in the inside corner and a slot 4.5 mm wide and 12 mm long on each leg ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DAn%2520L%2520bracket%252060%2520x%252060%2520mm%252C%252030%2520mm%2520wide%252C%25204%2520mm%2520thick%252C%2520with%2520a%2520gusset%2520in%2520the%2520inside%2520corner%2520and%2520a%2520slot%25204.5%2520mm%2520wide%2520and%252012%2520mm%2520long%2520on%2520each%2520leg))

## FAQ

### What is a boss on a 3D printed part?

A raised cylinder on a surface, usually with a hole in it for a screw. A boss that holds a circuit board off the floor of a case is called a standoff; 6 mm across with a 2.5 mm hole suits an M3 self-tapping screw.

### What is the difference between a rib and a gusset?

A rib is a thin wall added to stiffen a surface, such as the floor of a wide tray. A gusset is a triangular rib in an inside corner, between the two legs of a bracket. Neither should be thinner than 1.2 mm.

### What is the difference between a lip and a flange?

A lip is a small raised edge that stops something sliding or locates a lid. A flange is a flat rim sticking out sideways from the body, usually with screw holes, so that the part can be fixed down.

## About SpeakCAD

SpeakCAD is the most intuitive CAD for 3D printing, made for people who own a 3D printer and need a part that fits something they have: tap a face and type a size to shape it with simple tools, or describe it to the AI, on your phone or computer, and download a print-ready STL, 3MF or G-code sliced for your printer.

SpeakCAD works inside ChatGPT and Claude as a plugin (an MCP server): ask the assistant for a part with its measurements and SpeakCAD's own CAD AI designs it, shows it in 3D in the chat and hands over a print-ready STL, 3MF or G-code sliced for your printer.

- Live demo, no account: https://speakcad.com/demo
- In ChatGPT, Claude and other MCP clients: https://speakcad.com/chatgpt-plugin, https://speakcad.com/claude-connector, https://speakcad.com/mcp-server
- Pricing: https://speakcad.com/pricing
- FAQ: https://speakcad.com/faq
- Site index for AI assistants: https://speakcad.com/llms.txt
