---
title: "How to use digital callipers for 3D printing: four measurements, the zero and six mistakes"
description: "A digital calliper takes four measurements: outside, inside, depth and step. How to take each one, zero it, find a hole spacing, and avoid six mistakes."
canonical: https://speakcad.com/blog/how-to-use-digital-calipers-for-3d-printing
published: 2026-11-17
updated: 2026-11-17
publisher: SpeakCAD
---

# How to use digital callipers for 3D printing: four measurements, the zero and six mistakes

> A digital calliper takes four measurements: outside, inside, depth and step. How to take each one, zero it, find a hole spacing, and avoid six mistakes.

A digital calliper takes four kinds of measurement, and many new owners use just one: the big jaws round the outside of a thing. The other three measure the inside of a tube, the depth of a recess and the height of a step, and between them they cover what a printed part usually has to fit. Ten minutes with this page and the calliper in your hand is enough to learn all four.

## The parts, by what they measure

- **Outside jaws**: the two long jaws under the beam. They close round an object.
- **Inside jaws**: the two small pointed jaws on top. They open inside a hole or a slot.
- **Depth rod**: the thin blade that slides out of the far end of the beam as you open the jaws.
- **Step faces**: the flat end of the beam and the flat end of the slider, at the jaw end of the tool. They sit level with each other when the calliper reads zero.
- **Thumb wheel and lock screw**: the wheel moves the slider gently; the screw holds a reading while you lift the calliper out of an awkward spot.
- **ZERO and mm/in buttons**: more on both below.

## Before you measure: clean, close, zero

Wipe the jaw faces with a finger, close them gently, and press ZERO. Open and close them again: the display should come back to 0.00. If it does not, there is dust on a jaw. Then check that the display says mm. In inch mode every reading is 25.4 times smaller, and [a part built from inch numbers arrives the wrong size](/blog/3d-model-wrong-size-millimetres-or-inches).

## The four measurements

### 1. Outside: the big jaws

Put the object between the outside jaws, as deep in the jaws as it will go, and close them with the thumb wheel until they touch. Do not squeeze. Keep the jaws square to the object: a tilted calliper reads large, so rock it slightly and keep the **smallest** reading. That is the one taken square.

A round part needs no hunting for its widest point: two flat jaws closed on a tube span its full diameter. Turn the tube a quarter turn and measure again, because tubes and moulded parts are rarely perfectly round.

### 2. Inside: the small jaws

Put the inside jaws into the hole or the slot and open them until they touch both sides.

- A round hole: rock gently and keep the **largest** reading. Anything less is a chord, not the diameter.
- A slot between two flat walls: keep the **smallest**, as for the outside jaws.

On a small hole the inside jaws read a little low, because their tips are narrow flats, not knife edges, and cannot reach the full width of a tight curve. Cross-check with the thing itself: the screw, or the plain shank of a drill bit of a known size.

### 3. Depth: the rod

Stand the end of the beam flat on the rim of the hole or the recess and open the calliper until the rod touches the bottom. Keep the beam upright; leaning it makes the reading long. Use it for how deep a pocket is, how far a button sits below a surface, or how much height there is under the lip of a shelf.

### 4. Step: the two end faces

Rest one step face on the upper surface and slide the other down to the lower one. This reads the height of a ledge, or how far a boss stands up, and it is steadier than the depth rod because the faces are wide.

## Hole spacing, with the zero trick

The distance between two hole centres cannot be read directly: there is nothing at a centre to touch. Two ways round it.

1. **Same side to same side.** Measure from the left side of one hole to the left side of the next. That distance equals the centre spacing, as long as the two holes are the same size.
2. **The zero trick.** Measure one hole's diameter with the inside jaws and press ZERO while they are still in the hole. Now put the inside jaws across both holes, far side to far side. The display shows the centre spacing, because the diameter has already been taken off.

For a hole's distance from an edge, close the outside jaws on the strip of material between the edge and the hole, then add half the hole's diameter.

## How far to trust the number

The display shows hundredths of a millimetre. Write down tenths. A printed hole comes out 0.2 to 0.4 mm smaller than drawn and an outside wall a tenth or two fatter, so the gap you design in matters more than the last digit on the screen.

What you do need is the same answer twice. Measure every dimension that decides a fit **three times, at three places**, then:

- for something your part goes **around** (a shaft, a tube, a phone), keep the largest reading;
- for something your part goes **into** (a hole, a slot, a drawer), keep the smallest.

That way the part fits at the tightest spot.

## Six mistakes that cost a reprint

1. **Squeezing.** Plastic, rubber and cardboard give under the jaws. Close with the wheel until the jaws touch, no further.
2. **Measuring on the tips.** The thin ends of the jaws flex and tilt. Seat the object deep, near the beam.
3. **Skipping the zero.** A calliper zeroed with the jaws slightly open adds that error to every number of the session.
4. **Inch mode.** A 30 mm width reads 1.181 and looks plausible at a glance.
5. **Measuring the middle.** A remote is wider at one end, a bottle bulges, a moulded case tapers. Measure along the whole length of anything your part goes around, and keep the widest reading.
6. **Measuring the old printed part, not the thing it fits.** You copy the old part's errors and add your printer's. Measure the object.

## From the reading to the part

Write each number down with what it is ("tube, outside, 25.4"), then add the clearance for the fit you want: 0.2 mm per side for a cap that stays on, 0.5 mm for something that slides. [How much clearance to leave](/blog/3d-printing-clearance-how-much-gap-to-leave) has the table, and [inside or outside?](/blog/inside-or-outside-dimensions-3d-printed-box) shows how the numbers add up for a box or a sleeve.

In SpeakCAD every size and position is typed in millimetres, so the numbers on your notepad go in as they are. Once the part is built, the Measure tool reads any distance back with two taps, and for the one fit that matters, [Fit Check](/guides/fit-check-parts-that-fit-first-time) cuts a five-minute test slice to print before the whole part.

[Which measurements a part needs](/blog/how-to-measure-an-object-for-a-3d-printed-part) is its own article. No callipers in the house yet? [Six ways to measure without them](/blog/measure-for-3d-printing-without-calipers) will get a first part made tonight. And [CAD for beginners](/cad-for-beginners) starts from the idea these numbers serve: in CAD a size is a number you type, not a shape you drag.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

## Prompts to try

- A cap for a tube 25.4 mm outside diameter, 15 mm deep, 0.2 mm clearance per side, 1.6 mm wall, closed end ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520cap%2520for%2520a%2520tube%252025.4%2520mm%2520outside%2520diameter%252C%252015%2520mm%2520deep%252C%25200.2%2520mm%2520clearance%2520per%2520side%252C%25201.6%2520mm%2520wall%252C%2520closed%2520end))
- A plate 80 x 40 x 3 mm with two M4 clearance holes 52 mm apart, centred on the plate ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520plate%252080%2520x%252040%2520x%25203%2520mm%2520with%2520two%2520M4%2520clearance%2520holes%252052%2520mm%2520apart%252C%2520centred%2520on%2520the%2520plate))
- A sleeve for a remote 148 x 42 x 18 mm at its widest, open at one end, 0.5 mm clearance all round, 1.6 mm walls ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520sleeve%2520for%2520a%2520remote%2520148%2520x%252042%2520x%252018%2520mm%2520at%2520its%2520widest%252C%2520open%2520at%2520one%2520end%252C%25200.5%2520mm%2520clearance%2520all%2520round%252C%25201.6%2520mm%2520walls))

## FAQ

### How do you measure the inside of a hole with callipers?

With the two small jaws on top. Put them in the hole, open them until they touch both sides, rock the calliper gently and keep the largest reading, which is the diameter. On a small hole the inside jaws read slightly low, so cross-check with the screw or a drill bit shank that fits it.

### How accurate do measurements need to be for 3D printing?

To the nearest 0.1 mm for anything that decides a fit. The calliper displays hundredths, but a printed hole comes out 0.2 to 0.4 mm smaller than drawn, so the clearance you add matters more than the last digit. Measure three times at three places.

### How do I measure the distance between two hole centres?

Measure one hole's diameter with the inside jaws and press ZERO while they are in the hole, then measure across both holes from far side to far side: the display shows the centre spacing. Or measure from the left side of one hole to the left side of the other, which equals the centre spacing when the holes are the same size.

### Should callipers be set to mm or inches for 3D printing?

Millimetres. Slicers read model files as millimetres, and nozzles, layers and clearances are all given in them. A number typed from inch mode makes a part 25.4 times too small.

## About SpeakCAD

SpeakCAD is the most intuitive CAD for 3D printing, made for people who own a 3D printer and need a part that fits something they have: tap a face and type a size to shape it with simple tools, or describe it to the AI, on your phone or computer, and download a print-ready STL, 3MF or G-code sliced for your printer.

SpeakCAD works inside ChatGPT and Claude as a plugin (an MCP server): ask the assistant for a part with its measurements and SpeakCAD's own CAD AI designs it, shows it in 3D in the chat and hands over a print-ready STL, 3MF or G-code sliced for your printer.

- Live demo, no account: https://speakcad.com/demo
- In ChatGPT, Claude and other MCP clients: https://speakcad.com/chatgpt-plugin, https://speakcad.com/claude-connector, https://speakcad.com/mcp-server
- Pricing: https://speakcad.com/pricing
- FAQ: https://speakcad.com/faq
- Site index for AI assistants: https://speakcad.com/llms.txt
