---
title: "How to measure an object for a 3D printed part that fits (calliper, ruler or phone)"
description: "Which measurements a printed part needs, how exact each must be, when a ruler is enough, and how to write them down so the part fits the first time."
canonical: https://speakcad.com/blog/how-to-measure-an-object-for-a-3d-printed-part
published: 2026-10-19
updated: 2026-10-19
publisher: SpeakCAD
---

# How to measure an object for a 3D printed part that fits (calliper, ruler or phone)

> Which measurements a printed part needs, how exact each must be, when a ruler is enough, and how to write them down so the part fits the first time.

Most parts that come off a printer and do not fit were not printed wrong. They were measured wrong, or not measured at all: the width was guessed from a photo, the hole spacing was read off one hole and assumed for the rest, the lid was sized to the box without the 0.3 mm the plastic needs. Measuring takes ten minutes. It is the one step that decides whether the print fits.

## The tool: a calliper for fits, a ruler for everything else

A digital calliper is the best 20 dollars a printer owner spends. It reads to 0.01 mm, it measures outside widths with its big jaws, inside widths with the small ones on top, and depths with the rod that slides out of the end. You do not need the precision; you need the repeatability. A ruler read by eye lands within half a millimetre on a good day, which is fine for a drawer insert and fatal for a lid.

The rule: **if the dimension decides a fit, use a calliper. If a millimetre either way does not matter, a ruler is fine.**

| Measurement | Ruler is fine | Calliper |
|---|---|---|
| Outside size of a thing you make a holder for | ✓ (add clearance anyway) | better |
| Inside of a drawer, a shelf, a cupboard | ✓ | |
| A shaft, a pin, a tube that must press or slide in | | ✓ |
| A hole pattern (screw spacing) | | ✓ |
| A battery, a board, a tracker that must click in | | ✓ |
| A wall thickness you must match | | ✓ |

No calliper tonight? A phone photo of the object on a ruler, taken straight from above, is good to about 0.5 mm, and the [photo to part](/duplicate) route in SpeakCAD reads that photo for you. Round up to the next half millimetre and add a little more clearance than usual.

## What to measure, in order

1. **The envelope.** Length, width and height of the thing the part must hold or fit around. Measure at the widest point, not the middle: a remote control is wider at the top, a power bank has a bulge at the buttons.
2. **The one dimension that decides the fit.** The shaft that goes into the knob, the slot the tab slides into, the inside of the tube. Measure it three times at three places and keep the largest reading for a hole the part must go into, the smallest for a pin the part must go around.
3. **Feature positions, from one corner.** Where the buttons, ports and screw holes are, all measured from the same corner of the object, not from each other. Chained measurements add their errors; from-one-corner measurements do not.
4. **Hole spacing, the honest way.** Measure from the left edge of one hole to the left edge of the next. Centre to centre is impossible to read; same-edge to same-edge gives the centre spacing exactly.
5. **Depths.** How deep the part may go before it hits something: the thickness of the shelf, the depth of the drawer, the height under the desk.
6. **What is in the way.** The screw heads, the cable, the hinge: anything the new part must leave room for.

## How exact is exact enough

Printed PLA and PETG are predictable: holes come out 0.2 to 0.4 mm smaller than drawn, outside walls a tenth or two bigger. So a measurement to the nearest 0.1 mm is plenty, and the clearance you add matters more than the last decimal. [How much clearance to leave](/blog/3d-printing-clearance-how-much-gap-to-leave) has the table; the short version is 0.2 mm per side for a snug fit, 0.5 mm for a part that slides, 1 mm for a holder something drops into.

## Write it down as a spec, not a story

Write the numbers in millimetres on one line each before you open any software. It stops you inventing a value halfway through. A spec that works:

- Power bank: 142 × 68 × 15.5 mm, buttons on one short side 20 mm from the corner
- Holder screws to the wall with two M4 countersunk screws, 60 mm apart
- Open top, 0.5 mm clearance all round, 2 mm walls, cable slot 12 mm wide at the bottom

Type exactly that into SpeakCAD and the AI builds a holder to those numbers, states the sizes it used in its reply, and the dimensions panel shows every one of them. Say what the part is for ("a holder for this power bank, screwed to the wall") as well as the numbers, because that is what decides the clearance it adds. If the object is a product with a name, the AI can look up its published measurements online first and tells you what it found; it still wants your calliper on the one dimension that decides the fit.

## Check before you print

Open the dimensions panel and read the part back against your spec: the inside of the pocket should be your measurement plus the clearance, the hole spacing exactly yours. Two taps with the Measure tool give any distance on the model. For the one fit that matters most, [Fit Check](/guides/fit-check-parts-that-fit-first-time) cuts a five-minute test slice around it: print that, report too tight, perfect or too loose, and the part is corrected before the long print.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a new part spends 4 credits on a plan with its first 3 small changes free, a design change 3, a small change 2, a quick edit 1; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

## Prompts to try

- A wall holder for a power bank 142 x 68 x 15.5 mm, open top, 0.5 mm clearance all round, 2 mm walls, two M4 countersunk screw holes 60 mm apart, cable slot 12 mm wide at the bottom ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520wall%2520holder%2520for%2520a%2520power%2520bank%2520142%2520x%252068%2520x%252015.5%2520mm%252C%2520open%2520top%252C%25200.5%2520mm%2520clearance%2520all%2520round%252C%25202%2520mm%2520walls%252C%2520two%2520M4%2520countersunk%2520screw%2520holes%252060%2520mm%2520apart%252C%2520cable%2520slot%252012%2520mm%2520wide%2520at%2520the%2520bottom))
- A cap for a 25.4 mm outside diameter tube, 15 mm deep, snug fit, 1.5 mm wall, closed end with a 5 mm drain hole ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520cap%2520for%2520a%252025.4%2520mm%2520outside%2520diameter%2520tube%252C%252015%2520mm%2520deep%252C%2520snug%2520fit%252C%25201.5%2520mm%2520wall%252C%2520closed%2520end%2520with%2520a%25205%2520mm%2520drain%2520hole))
- A bracket that clamps onto a 32 mm round table leg with two M5 bolts and holds a 10 mm hook ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520bracket%2520that%2520clamps%2520onto%2520a%252032%2520mm%2520round%2520table%2520leg%2520with%2520two%2520M5%2520bolts%2520and%2520holds%2520a%252010%2520mm%2520hook))

## FAQ

### Do I need a calliper for 3D printing?

For parts that must fit something, yes: a shaft, a hole pattern, a battery or a board need a reading to 0.1 mm, which a ruler cannot give. A ruler is fine for a drawer insert, a shelf or a holder where you add a millimetre of clearance anyway.

### How do I measure the distance between two holes?

Measure from the left edge of one hole to the left edge of the other with a calliper. That same-edge distance equals the centre-to-centre spacing exactly, which cannot be read directly.

### Can I measure an object with my phone for 3D printing?

A photo taken straight from above with a ruler in the frame is good to about half a millimetre. SpeakCAD reads that photo on its photo-to-part page; add a little more clearance than usual for a fit measured that way.

## About SpeakCAD

SpeakCAD is the most intuitive CAD for 3D printing, made for people who own a 3D printer and need a part that fits something they have: tap a face and type a size to shape it with simple tools, or describe it to the AI, on your phone or computer, and download a print-ready STL, 3MF or G-code sliced for your printer.

SpeakCAD works inside ChatGPT and Claude as a plugin (an MCP server): ask the assistant for a part with its measurements and SpeakCAD's own CAD AI designs it, shows it in 3D in the chat and hands over a print-ready STL, 3MF or G-code sliced for your printer.

- Live demo, no account: https://speakcad.com/demo
- In ChatGPT, Claude and other MCP clients: https://speakcad.com/chatgpt-plugin, https://speakcad.com/claude-connector, https://speakcad.com/mcp-server
- Pricing: https://speakcad.com/pricing
- FAQ: https://speakcad.com/faq
- Site index for AI assistants: https://speakcad.com/llms.txt