---
title: "Gridfinity vs IKEA Skådis vs French cleat in 2026: which organiser system to print for"
description: "Gridfinity for drawers, IKEA Skådis for a pegboard wall, a French cleat for heavy tools: the numbers that define each and what a printed holder needs to fit."
canonical: https://speakcad.com/blog/gridfinity-vs-ikea-skadis-vs-french-cleat-2026
published: 2026-11-17
updated: 2026-11-17
publisher: SpeakCAD
---

# Gridfinity vs IKEA Skådis vs French cleat in 2026: which organiser system to print for

> Gridfinity for drawers, IKEA Skådis for a pegboard wall, a French cleat for heavy tools: the numbers that define each and what a printed holder needs to fit.

They solve three different problems, so the choice is mostly about where your things live. Gridfinity organises flat surfaces: drawers and bench tops. IKEA Skådis is a pegboard for light things on the wall above a desk. A French cleat carries heavy tools on a workshop wall. Most workshops end up with two of the three, and a printer adds what none of them sells: the holder shaped to your own tool.

## The short answer

- **Small parts and tools in a drawer or on the bench: Gridfinity.** Bins drop onto a 42 mm grid and move in a second.
- **Light tools within reach above a desk: IKEA Skådis.** Buy the board, print the holders.
- **Heavy tools on a workshop wall: a French cleat.** The weight goes into the wall screws, not into a small hook.
- **A drawer whose contents never change: none of them.** A one-piece insert sized to the drawer wastes no space.

## Side by side

| | Gridfinity | IKEA Skådis | French cleat |
|---|---|---|---|
| Where it lives | Drawers, bench tops, shelves | A wall above a desk or a bench | A workshop or garage wall |
| What you buy | Nothing: plates and bins are printed | The board | Plywood strips and screws |
| The numbers that define it | A 42 mm grid, 7 mm height units | 5 × 15 mm slots 40 mm apart, a 5 mm board | A 45° bevel; the rest is yours |
| A printed accessory needs | The standard base under the bin | Two hooks 40 mm apart, and a pin below | A 45° hook matched to your strip |
| Carries | Whatever sits in a bin | Light to medium tools | The heaviest tools |
| Filament | PLA; PETG in a hot garage | PLA at a desk, PETG for weight | PETG |

## Gridfinity: drawers and bench tops

Gridfinity is a shared standard: a baseplate with a grid of sockets, and bins whose feet drop into them. Any bin fits any plate, which is why thousands of bins are published.

**The numbers.** The grid is 42 mm. A bin is 0.5 mm smaller than its grid span, so a 2 × 1 bin measures 83.5 × 41.5 mm. Height counts in units of 7 mm, base included: 3 units is 21 mm, 6 units 42 mm. The base is a profile of about 5 mm with chamfered feet, the same under every bin. Optional magnets are 6 × 2 mm, in a 6.5 mm pocket at each corner of each cell.

**What a printed accessory needs.** The standard base, exactly: it is the part you must not improvise. Above it, anything goes: dividers sized to your screwdrivers, a label tab, a finger scoop. Size the plate from the drawer (inside width and depth divided by 42, rounded down) and check your bed: a 4 × 4 bin is 167.5 mm square and fits a 180 mm bed, 5 × 5 needs 220 mm, 6 × 6 needs 256 mm. Bins print upright without supports, at 0.2 mm layers with 2 walls. [A custom Gridfinity bin](/blog/custom-gridfinity-bin-sized-to-what-it-holds) goes through it step by step, and [what bed size you need](/blog/what-print-bed-size-do-you-need) lists the common printers.

**Look elsewhere if** the drawer's contents never change. A drawer rarely divides by 42, so a strip at the edge is lost, and bins on a plate take more plastic than [one insert sized to the drawer](/blog/drawer-organizer-insert-sized-to-your-drawer).

## IKEA Skådis: a pegboard above the desk

Skådis is a fibreboard pegboard from IKEA with rows of short vertical slots where an ordinary pegboard has round holes. The board is bought. The holders are where a printer earns its place.

**The numbers.** The slots are 5 mm wide and 15 mm tall (measured boards run about 5.2 × 15.2 mm), 40 mm apart centre to centre along a row. Each row sits 20 mm lower than the one above and 20 mm to the side. The board is 5 mm thick.

**What a printed accessory needs.** Two hooks 40 mm apart at the top of a back plate. Each hook has a stem 4.6 mm thick that passes through the slot, with 0.2 mm of play on each side, and a leg 3.5 mm thick that hangs 7 mm behind the board. A holder you pull a tool out of also needs a pin in the staggered row below, 20 mm lower, so it cannot swing out. Print the holder standing as it hangs, so the layers run along the stem of each hook; the hook tips may want a small tree support. PLA is fine for pens and earbuds. Use PETG and 4 walls for batteries and drills, because PLA creeps under a constant load.

**Look elsewhere if** the tool is heavy and you pull on it hard, or you have no board and no wish to buy one.

## French cleat: heavy tools on the wall

A French cleat is two strips, each with one long edge cut at 45°. One is screwed to the wall with its bevel up and sloping back towards the wall. The other is fixed to the back of the holder, bevel down. Drop the holder on, and its weight pulls it down and in against the wall. Rows of strips turn a whole wall into storage you can rearrange.

**The numbers.** Only the 45° is fixed. The thickness and the height of the strips are whatever the builder cut, often 18 or 19 mm plywood, so there is no standard to design to: measure your own strip.

**What a printed accessory needs.** A hook on its back that mirrors your strip: a 45° lip, and a gap as wide as the strip is thick plus 0.5 mm, deep enough to seat fully. Lower on the back, a spacer as thick as the strip, so the holder hangs straight and does not tilt in. The hook carries everything, so [make it strong](/blog/how-to-make-3d-printed-parts-stronger-2026): print the holder on its side so the hook's outline is one continuous line on every layer, in PETG, with 4 to 5 walls and a 3 mm fillet inside the hook.

For the heaviest tools, do not print the hook at all. Cut a short cleat from the same plywood and screw the printed holder to it through two countersunk holes. The wood carries the load, and the print only has to hold the tool's shape.

**Look elsewhere if** you cannot put a row of screws in the wall, or you want small parts at hand: a cleat holds holders, not loose screws.

## When to mix them

- **Gridfinity below, Skådis above.** Small parts in the drawers, the tools you reach for on the board over the desk.
- **A cleat wall with Gridfinity on it.** A cleat-hung shelf with a baseplate on top, so a bin moves from the drawer to the wall and back.
- **Skådis for the light, a cleat for the heavy.** Pliers and screwdrivers on the pegboard, the drill and the clamps on the cleat beside it.
- **One holder, two backs.** The part that grips the tool is the same on a pegboard and on a cleat; only the back changes. Design the holder once, then ask for the other back.

## Designing the holder

Whichever system you choose, the work is the same: measure the tool at its widest, decide how it goes in and comes out, and put the right back on it. In SpeakCAD, name the system in the description and give its numbers: "two SKADIS hooks 40 mm apart for 5 × 15 mm slots", "a 45 degree cleat for a 19 mm strip", "a 2 × 3 Gridfinity bin, 6 units tall". The AI builds Gridfinity bins on the standard base; pegboard hooks or a cleat on the back are one more sentence. The [holder generator](/holder-generator) starts from the object you measure, the [bracket generator](/bracket-generator) from the screws and the load, and the [library](/library) has Gridfinity bins, pegboard holders and cleat racks to start from.

One warning for all three: never scale a download in the slicer to make it fit your tool. Scaling stretches the interface too. At 110% a 4.6 mm Skådis stem becomes 5.1 mm and no longer enters its slot, and a Gridfinity foot no longer seats. Change the part that holds the tool, and leave the interface alone. [The best prints for the workshop and garage](/blog/best-3d-prints-for-the-workshop-and-garage-2026) has more parts worth designing this way.

SpeakCAD is not affiliated with IKEA.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

## Prompts to try

- A 2 x 2 Gridfinity bin, 6 units tall, with one divider across the middle, a label tab on the front, a stacking lip and no magnets ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%25202%2520x%25202%2520Gridfinity%2520bin%252C%25206%2520units%2520tall%252C%2520with%2520one%2520divider%2520across%2520the%2520middle%252C%2520a%2520label%2520tab%2520on%2520the%2520front%252C%2520a%2520stacking%2520lip%2520and%2520no%2520magnets))
- An IKEA SKADIS holder for a cordless screwdriver: a cradle 45 mm wide and 60 mm deep, a 4 mm back plate 80 x 70 mm, two SKADIS hooks 40 mm apart at the top for the 5 x 15 mm slots of the 5 mm board and an anti-swing pin 20 mm lower, 2.4 mm walls ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DAn%2520IKEA%2520SKADIS%2520holder%2520for%2520a%2520cordless%2520screwdriver%253A%2520a%2520cradle%252045%2520mm%2520wide%2520and%252060%2520mm%2520deep%252C%2520a%25204%2520mm%2520back%2520plate%252080%2520x%252070%2520mm%252C%2520two%2520SKADIS%2520hooks%252040%2520mm%2520apart%2520at%2520the%2520top%2520for%2520the%25205%2520x%252015%2520mm%2520slots%2520of%2520the%25205%2520mm%2520board%2520and%2520an%2520anti-swing%2520pin%252020%2520mm%2520lower%252C%25202.4%2520mm%2520walls))
- A French cleat holder for a cordless drill: a shelf 90 mm wide and 80 mm deep with a 40 mm slot for the handle, 5 mm thick, a 45 degree cleat on the back for a 19 mm plywood strip with 0.5 mm clearance, and a spacer at the bottom so it hangs straight ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520French%2520cleat%2520holder%2520for%2520a%2520cordless%2520drill%253A%2520a%2520shelf%252090%2520mm%2520wide%2520and%252080%2520mm%2520deep%2520with%2520a%252040%2520mm%2520slot%2520for%2520the%2520handle%252C%25205%2520mm%2520thick%252C%2520a%252045%2520degree%2520cleat%2520on%2520the%2520back%2520for%2520a%252019%2520mm%2520plywood%2520strip%2520with%25200.5%2520mm%2520clearance%252C%2520and%2520a%2520spacer%2520at%2520the%2520bottom%2520so%2520it%2520hangs%2520straight))

## FAQ

### Gridfinity or IKEA Skådis: which is better?

They do different jobs. Gridfinity organises drawers and bench tops with bins on a 42 mm grid; Skådis is a pegboard for light tools on a wall above a desk. Many workshops use both: small parts in Gridfinity drawers, and the tools you reach for on the board.

### What are the IKEA Skådis hole dimensions?

The slots are 5 mm wide and 15 mm tall, 40 mm apart centre to centre in a row, and each row is staggered 20 mm down and 20 mm sideways from the one above. The board is 5 mm thick. Measured boards run about 5.2 × 15.2 mm, so a printed hook stem of 4.6 mm slides in without force.

### What are the Gridfinity dimensions?

The grid is 42 mm, and a bin is 0.5 mm smaller than its grid span, so a 2 × 1 bin measures 83.5 × 41.5 mm. Height counts in 7 mm units, base included: 3 units is 21 mm, 6 units 42 mm. Magnets are 6 × 2 mm in a 6.5 mm pocket at each corner of each cell.

### What angle is a French cleat, and is there a standard size?

The bevel is 45° on both strips. Nothing else is standard: the strips are whatever thickness and height the builder cut, often 18 or 19 mm plywood. Measure your own strip, and give a printed hook a gap 0.5 mm wider than it.

### Can a 3D printed French cleat hold heavy tools?

A printed cleat hook holds best printed on its side in PETG, with 4 to 5 walls and a fillet inside the hook, so the load runs along the layers. For the heaviest tools, cut the cleat from plywood and screw the printed holder to it: the wood carries the load and the print only holds the tool.

## About SpeakCAD

SpeakCAD is the most intuitive CAD for 3D printing, made for people who own a 3D printer and need a part that fits something they have: tap a face and type a size to shape it with simple tools, or describe it to the AI, on your phone or computer, and download a print-ready STL, 3MF or G-code sliced for your printer.

SpeakCAD works inside ChatGPT and Claude as a plugin (an MCP server): ask the assistant for a part with its measurements and SpeakCAD's own CAD AI designs it, shows it in 3D in the chat and hands over a print-ready STL, 3MF or G-code sliced for your printer.

- Live demo, no account: https://speakcad.com/demo
- In ChatGPT, Claude and other MCP clients: https://speakcad.com/chatgpt-plugin, https://speakcad.com/claude-connector, https://speakcad.com/mcp-server
- Pricing: https://speakcad.com/pricing
- FAQ: https://speakcad.com/faq
- Site index for AI assistants: https://speakcad.com/llms.txt
