---
title: "The best 3D prints for your desk setup in 2026, sized to your own gear (with the prompts)"
description: "Ten desk prints worth designing rather than downloading: hooks, under-desk mounts, trays, stands and holders, each with what to measure and its prompt."
canonical: https://speakcad.com/blog/best-3d-prints-for-your-desk-setup-2026
published: 2026-11-17
updated: 2026-11-17
publisher: SpeakCAD
---

# The best 3D prints for your desk setup in 2026, sized to your own gear (with the prompts)

> Ten desk prints worth designing rather than downloading: hooks, under-desk mounts, trays, stands and holders, each with what to measure and its prompt.

The best desk prints are the ones no model site can size for you: the hook that fits your desk's thickness, the tray that sits on your monitor stand, the holder cut for the hub you own. Here are 10, each with the one measurement that decides the fit and a prompt to paste into SpeakCAD with your number in it. Where a download or a shop part is the better answer, the item says so.

## The short answer

- **Print first: the headphone hook and the power strip brackets.**
- **Most used: the pen and tool tray**, laid out around what is on the desk now.
- **Download or buy instead:** a cradle moulded to one controller, an articulated arm, a monitor riser. SpeakCAD is a CAD for functional parts with real sizes, not for sculpted shapes.

Every prompt carries example sizes: swap in yours. The gaps follow the [clearance table](/blog/3d-printing-clearance-how-much-gap-to-leave): about 0.5 mm per side where something slides in and out, 0.2 to 0.3 mm where it should stay put.

## 1. A headphone hook that slips onto your desk edge

**Measure:** the desk top's thickness at the edge (25 mm here; measure yours). The gap is that plus 0.3 mm per side.

> A headphone hook that slips onto a desk edge 25 mm thick: a C clamp 30 mm wide with a 25.6 mm gap, 60 mm deep, 4 mm walls, and below it an arm 45 mm long with a 20 mm upturned tip, rounded on top, printed lying on its side

**Look elsewhere if** the edge is bevelled or framed underneath: screw on the hook from [20 useful prints from one sentence](/blog/20-useful-3d-prints-you-can-generate-from-one-sentence).

## 2. Brackets that hold the power strip under the desk

**Measure:** the strip's width and height at its fattest point, switch included.

> Two brackets that hold a power strip 52 mm wide and 40 mm tall under a desk: each a U shape 20 mm long with 0.5 mm clearance and 3 mm walls, and a flange on both sides with a 4.5 mm hole for a 4 mm wood screw

**Look elsewhere if** the top is glass: a clamp-on tray from a shop needs no drilling.

## 3. A cradle for the power brick

**Measure:** the brick's length, width and height at the widest point. Leave the ends open for the cables, ask for slots because a brick needs air, and print in PETG: PLA softens at around 55 to 60 °C.

> An under-desk cradle for a power brick 150 x 65 x 30 mm: two U-shaped rails 25 mm long with 1 mm clearance and 3 mm walls, ventilation slots in the floor of each, and a 4.5 mm screw hole in each flange

**Look elsewhere if** the thing to hang is a desktop computer: that weight belongs on a steel bracket.

## 4. A tray on the monitor stand's foot

**Measure:** the foot's width and depth, and the neck where the stand rises, which gets a cutout.

> A tray that sits on a monitor stand foot 220 x 180 mm: 20 mm tall with 1.6 mm walls and a 1.2 mm floor, a cutout 62 x 45 mm at the back for the stand's neck, three compartments, split into two halves that fit a 220 mm bed

**Look elsewhere if** you want the screen higher: a board on four printed feet is stronger than a printed riser, which is also wider than most beds.

## 5. A cable comb for the back edge

**Measure:** each cable's diameter with a calliper, in the order the cables leave the desk.

> A cable comb that screws to the back edge of a desk: a strip 120 x 20 mm and 3 mm thick with five round slots for cables of 4, 4, 5, 6 and 8 mm, each opening 1 mm narrower than its cable, and two countersunk holes for 4 mm screws

[How to design cable clips and cable management](/blog/how-to-design-cable-clips-and-cable-management-2026) covers the clip types and PLA against PETG. **Look elsewhere if** any size will do: a bag of adhesive clips is quicker.

## 6. A stand for the laptop or the tablet

**Measure:** the device's thickness at its thickest point, feet or case included. The slot is that plus 1 mm. A closed laptop stands upright in a wide block; a tablet leans at 60 to 70°, and [the stand guide](/blog/phone-and-tablet-stand-angle-size-design) has the lip and the base depth for it.

> A vertical stand for a closed laptop 16 mm thick: a block 150 mm long, 110 mm wide and 40 mm tall with a slot 17 mm wide and 30 mm deep along its length, slot edges rounded 1 mm, and four pockets 10 mm across underneath for rubber feet

**Look elsewhere if** you want the laptop open, raised and tilted: a metal stand carries that heat and weight better, and the part is wider than most beds.

## 7. A pen and tool tray laid out around your things

**Measure:** each group of things the way you would like to find them, plus 5 mm for fingers.

> A desk tray 240 x 90 x 22 mm with 1.6 mm walls and a 1.2 mm floor: a pen compartment 160 x 30 mm, one 80 x 80 mm for sticky notes, one 40 x 40 mm for clips, a slot 2.5 mm wide for a steel ruler, rounded outside corners

It is also a part to shape by hand, free: a box hollowed with Shell, dividers placed with Add. **Look elsewhere if** it goes in a drawer: [the drawer organiser guide](/blog/drawer-organizer-insert-sized-to-your-drawer) covers tapering drawers and splitting for the bed.

## 8. A holder for the dock or the USB hub

**Measure:** the hub's length, width and thickness, and which sides carry ports. Measure the plugs you use, not the sockets: a USB-C plug with its shell is about 12 x 7 mm.

> An under-desk holder for a USB hub 110 x 45 x 15 mm: a sleeve with 0.5 mm clearance and 2 mm walls, open along the long side with the ports and at the cable end, a thumb cutout to push the hub out, and two countersunk holes for 4 mm screws

**Look elsewhere if** the dock runs hot to the touch: leave it in open air.

## 9. A controller stand

A cradle that follows one controller's curves is a job for a model site ([where to download STL files](/blog/best-sites-to-download-stl-files-2026)). **Measure:** the width across the two grips, and how thick one grip is.

> A controller stand: a base 130 x 90 mm and 4 mm thick, a back rest 100 mm wide and 70 mm tall leaning back 20 degrees, a front lip 12 mm high, and 32 mm between the lip and the back rest for the grips, all edges rounded 2 mm

## 10. A mount for the webcam or the light

**Measure:** the thickness of the shelf or the screen edge it sits on. If the camera or the light has a tripod socket (a 1/4-20 thread), do not print the thread: leave a 6.5 mm hole and use a real tripod screw.

> A shelf-edge mount for a small light: a clamp for a shelf 18 mm thick with an 18.6 mm gap, 50 mm deep, 4 mm walls, and on top a platform 40 x 40 mm and 5 mm thick with a 6.5 mm hole in its centre for a tripod screw

**Look elsewhere if** it needs a ball joint or a friction hinge: buy the arm and print the adapter.

## How we picked

1. **Does it have to fit something only you own?** If any size will do, a download is quicker.
2. **Is it one measurement and one sentence?** Ten measurements make a project, not a desk print.
3. **Does it print flat, without supports, on a bed of 180 to 256 mm?**
4. **Is plastic the right material?** Not for a monitor's weight, and not next to real heat.

## From the prompt to the desk

For the hook's gap, the laptop slot or the hub's sleeve, [Fit Check](/guides/fit-check-parts-that-fit-first-time) cuts a five-minute test slice of the fit before the long print. The file leaves as an STL, a 3MF or G-code sliced for one of 380+ printers, and the [print time calculator](/3d-print-time-calculator) says how long your printer will take.

Shaping a part by hand (a hole, a cut, an added shape, text, rounded corners, a shell, every size typed in millimetres) is free, and so is downloading what you shaped. With the AI, a request spends credits for the work it takes: a quick edit usually 1–2, a small change 1–2, a new part or a design change 3–8, never more than 15 credits; on a plan the first 3 small changes of each part are free; without a plan a new part spends 3. Start with Maker: 50 credits a month for $7.99, cancel anytime.

## Prompts to try

- A headphone hook that slips onto a desk edge 25 mm thick: a C clamp 30 mm wide with a 25.6 mm gap, 60 mm deep, 4 mm walls, and below it an arm 45 mm long with a 20 mm upturned tip, its top rounded so it does not dent the headband, printed lying on its side ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DA%2520headphone%2520hook%2520that%2520slips%2520onto%2520a%2520desk%2520edge%252025%2520mm%2520thick%253A%2520a%2520C%2520clamp%252030%2520mm%2520wide%2520with%2520a%252025.6%2520mm%2520gap%252C%252060%2520mm%2520deep%252C%25204%2520mm%2520walls%252C%2520and%2520below%2520it%2520an%2520arm%252045%2520mm%2520long%2520with%2520a%252020%2520mm%2520upturned%2520tip%252C%2520its%2520top%2520rounded%2520so%2520it%2520does%2520not%2520dent%2520the%2520headband%252C%2520printed%2520lying%2520on%2520its%2520side))
- Two brackets that hold a power strip 52 mm wide and 40 mm tall under a desk: each a U shape 20 mm long with 0.5 mm clearance and 3 mm walls, a flange on both sides, and a 4.5 mm hole in each flange for a 4 mm wood screw ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DTwo%2520brackets%2520that%2520hold%2520a%2520power%2520strip%252052%2520mm%2520wide%2520and%252040%2520mm%2520tall%2520under%2520a%2520desk%253A%2520each%2520a%2520U%2520shape%252020%2520mm%2520long%2520with%25200.5%2520mm%2520clearance%2520and%25203%2520mm%2520walls%252C%2520a%2520flange%2520on%2520both%2520sides%252C%2520and%2520a%25204.5%2520mm%2520hole%2520in%2520each%2520flange%2520for%2520a%25204%2520mm%2520wood%2520screw))
- An under-desk holder for a USB hub 110 x 45 x 15 mm: a sleeve with 0.5 mm clearance and 2 mm walls, open along the long side with the ports and at the cable end, a thumb cutout to push the hub out, and two countersunk holes for 4 mm screws ([open in SpeakCAD](https://app.speakcad.com/signup?next=%2F%3Fprompt%3DAn%2520under-desk%2520holder%2520for%2520a%2520USB%2520hub%2520110%2520x%252045%2520x%252015%2520mm%253A%2520a%2520sleeve%2520with%25200.5%2520mm%2520clearance%2520and%25202%2520mm%2520walls%252C%2520open%2520along%2520the%2520long%2520side%2520with%2520the%2520ports%2520and%2520at%2520the%2520cable%2520end%252C%2520a%2520thumb%2520cutout%2520to%2520push%2520the%2520hub%2520out%252C%2520and%2520two%2520countersunk%2520holes%2520for%25204%2520mm%2520screws))

## FAQ

### What are the most useful 3D prints for a desk setup?

The ones sized to your own gear: a headphone hook that fits the desk's thickness, brackets that hold the power strip and its brick under the top, a tray laid out around your pens and tools, a stand for the laptop or tablet at your angle, and a holder for the dock or hub. Each needs one measurement, and each is a fixed, wrong size when downloaded.

### How do I size a 3D printed headphone hook for my desk?

Measure the thickness of the desk top at its edge with a calliper and make the hook's gap that plus about 0.3 mm per side, so 25.6 mm for a 25 mm top. Make the clamp 4 mm thick, round the top of the arm so it does not dent the headband, and print the hook lying on its side so the layers run along the load.

### Can I 3D print a monitor riser?

You can print its feet, and a tray for the stand's foot, but the riser itself is usually wider than a print bed and carries the monitor's weight. A wooden board on four printed feet is stronger and quicker than a riser printed in pieces.

### Which filament should I use for desk accessories?

PLA for trays, stands and hooks that stay cool indoors. PETG for anything under the desk next to a power brick, on a sunny windowsill or that has to flex, because PLA softens at around 55 to 60 °C and snaps rather than bends.

## About SpeakCAD

SpeakCAD is the most intuitive CAD for 3D printing, made for people who own a 3D printer and need a part that fits something they have: tap a face and type a size to shape it with simple tools, or describe it to the AI, on your phone or computer, and download a print-ready STL, 3MF or G-code sliced for your printer.

SpeakCAD works inside ChatGPT and Claude as a plugin (an MCP server): ask the assistant for a part with its measurements and SpeakCAD's own CAD AI designs it, shows it in 3D in the chat and hands over a print-ready STL, 3MF or G-code sliced for your printer.

- Live demo, no account: https://speakcad.com/demo
- In ChatGPT, Claude and other MCP clients: https://speakcad.com/chatgpt-plugin, https://speakcad.com/claude-connector, https://speakcad.com/mcp-server
- Pricing: https://speakcad.com/pricing
- FAQ: https://speakcad.com/faq
- Site index for AI assistants: https://speakcad.com/llms.txt
